GIGAswitch System ------------------------------------------------------------ Installation and Service Manual Order Number: EK-GGSVA-IN-001 This document provides qualified DIGITAL service personnel with instructions for installing, and servicing the GIGAswitch System hardware. Revision/Update Information: This is a new document. Digital Equipment Corporation Maynard, Massachusetts ------------------------------------------------------------ First Printing, August 1993 While Digital believes that information included in this publication is correct as of the date of publication, it is subject to change without notice Digital Equipment Corporation makes no representations that the interconnection of its products in the manner described in this document will not infringe existing or future patent rights, nor do the descriptions contained in this document imply the granting of licenses to make, use, or sell equipment or software in accordance with the description. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction document, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user 's own expense. Copyright © Digital Equipment Corporation 1993. All Rights Reserved. Printed in the United States of America. The postpaid Reader 's Comments forms at the end of this document request your critical evaluation to assist in preparing future documentation. The following are trademarks of Digital Equipment Corporation: DECconnect, GIGAswitch, ThinWire, and the DIGITAL Logo. All other trademarks and registered trademarks are the property of their respective holders. This document was prepared using VAX DOCUMENT, Version 2.1. ------------------------------------------------------------ Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Part I Install 1 Overview of the GIGAswitch System Purpose of the GIGAswitch System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Parts of the GIGAswitch System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Location of the Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Description of the Cooling and Power Modules . . . . . . . . . . . . . . . . . . . . . 1-6 Description of the Logic Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 2 Preparing to Install the System Verifying the Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Unpacking the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Testing the System Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Preparing the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 Setting Up ESD Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20 Removing the System Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21 Installing the PMD Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25 Installing the MMF ANSI MIC PMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26 Installing the SMF PMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31 3 Installing the GIGAswitch System Installing the GIGAswitch System in the Rack . . . . . . . . . . . . . . . . . . . . . 3-3 Attaching the Upper Plenum to the GIGAswitch System . . . . . . . . . . . . . 3-7 Installing the System Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Part II Test 4 Preparing to Test the System Connecting the OBM terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Setting the Security Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 iii 5 Testing the System Diagnostic Mode Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Help Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Initiating the MST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Testing Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12 Meaning of LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 Part III Service 6 Preparing to Replace Modules Prerequisites for Replacing GIGAswitch System Modules . . . . . . . . . . . . . 6-2 Setting Up ESD Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Removing Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 7 Replacing Modules Replacing a Logic Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Replacing the PMD Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 Removing the MMF ANSI MIC PMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6 Installing the MMF ANSI MIC PMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9 Removing the SMF PMD Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . 7-12 Installing the SMF PMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15 Replacing a Blank Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20 Replacing a Fan Tray Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22 Replacing a FEU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24 Replacing a Power Supply Filler Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26 Replacing a PSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-28 Replacing a PSC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-30 8 Removing the System from the Rack Removing the Upper Plenum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Detaching the Empty GIGAswitch System from the Rack . . . . . . . . . . . . . 8-3 Lowering the Empty GIGAswitch System . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 9 Replacing Backplanes Accessing the Backplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Replacing the Power Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Replacing the Logic Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10 Restoring the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15 Part IV Reference iv A GIGAswitch System Specifications Physical Dimensions of the GIGAswitch System . . . . . . . . . . . . . . . . . . . . A-3 Electrical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4 Environmental Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6 B Cooling and Power Modules Fan Tray Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 FEU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 PSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 PSC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6 C Logic Modules Line Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2 PMD Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5 SCP Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6 Clock Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9 CBS Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-12 D Guidelines for Installing Additional Modules Identifying the Contents of the GIGAswitch System . . . . . . . . . . . . . . . . . D-2 Recommended Location for Logic Modules . . . . . . . . . . . . . . . . . . . . . . . . . D-4 Index v ------------------------------------------------------------ Preface This document provides qualified DIGITAL service personnel with instructions for installing, and servicing the GIGAswitch System hardware. Intended Audience This document is intended for DIGITAL service personnel who are experienced in installing and servicing network hardware. vii Document Structure This document is structured as follows: Part I contains overview information and instructions for installing the GIGAswitch System: · Chapter 1 describes the GIGAswitch System and its component modules. · Chapter 2 describes the procedures that you must complete before installing the GIGAswitch System. These procedures include verifying the site preparation, unpacking the system, testing the system modules, installing the lower plenum in the rack, setting up electrostatic discharge (ESD) protection, and removing the modules. · Chapter 3 describes the procedures for installing the GIGAswitch System. These procedures include lifting the empty GIGAswitch System onto the lower plenum, attaching the GIGAswitch System to the rack, installing the upper plenum, and installing the modules. Part II contains information for testing the GIGAswitch System: · Chapter 4 describes the procedures that you must complete before testing the GIGAswitch System. These procedures include connecting the out-of-band management (OBM) terminal, and setting the security switch. · Chapter 5 describes the procedures for initiating the module self-tests (MSTs) and provides instructions for evaluating the results of the MSTs. Part III contains information for replacing the field replaceable units (FRUs) · Chapter 6 describes the replacement requirements for each GIGAswitch System module, and describes the procedures used in replacing some of the GIGAswitch System modules. These procedures include setting up electrostatic discharge (ESD) protection, and removing or applying system power. · Chapter 7 describes the procedures for replacing the cooling and power modules and the logic modules. Cooling and power modules include modules of the fan tray assembly, front end unit (FEU), power status assembly (PSA) , and power system controller (PSC) families. Logic modules include modules of the line card, physical medium dependent (PMD) daughter card, switch control processor (SCP), clock card (CLK), and crossbar switch (CBS) families. · Chapter 8 describes the procedure for removing the GIGAswitch System. · Chapter 9 describes the procedures for replacing the power and logic backplanes. viii Part IV contains reference information. · Appendix A provides the physical, electrical, and environmental specifications for the GIGAswitch System. · Appendix B describes the cooling and power modules in the fan tray assembly, FEU, PSA, and the PSC card families. · Appendix C describes the logic modules in the line card, physical medium dependent (PMD) daughter card, SCP card, CBS card, and clock card families. · Appendix D provides guidelines for installing additional logic modules. Customer Documentation The customer GIGAswitch System documentation set consists of the following documents: ------------------------------------------------------------ document Part Number ------------------------------------------------------------ GIGAswitch System Manager 's Guide EK-GGMGA-MG ------------------------------------------------------------ Internal Documentation The internal GIGAswitch System documentation set is for DIGITAL internal use only. This documentation set includes this manual and the following documents: ------------------------------------------------------------ document Part Number ------------------------------------------------------------ GIGAswitch System Maintenance Card EK-GGGSV-CD GIGAswitch System Installation Card EK-GGGIN-CD ------------------------------------------------------------ Related Documentation Additional information is available in the following documents: ------------------------------------------------------------ document Part Number ------------------------------------------------------------ Fiber Distributed Data Interface Media Connection Information EK-A0597-M1 DECconnect System Requirements Evaluation Workbook EK-DECSY-EG ------------------------------------------------------------ ix Conventions The following conventions are used in this document: Bold typeface Indicates that a word or phrase is being emphasized to the reader. Italic typeface Indicates the complete titles of manuals. ------------------------------------------------------------ ------------------------------------------------------------ Return ------------------------------------------------------------ ------------------------------------------------------------ Indicates that you press the return key on the keyboard. ------------------------------------------------------------ ------------------------------------------------------------ Ctrl/O ------------------------------------------------------------ ------------------------------------------------------------ Indicates that you must hold down the key labeled Ctrl while you press another key or a pointing device button. x Safety Symbols ------------------------------------------------------------ Number Symbol Description ------------------------------------------------------------ ! Caution - Rotating fans Allow the fans to run down before removing the fan tray from the unit. " Caution Remove system power before removing or installing the system module. # Warning The weight of this unit when empty is 31.75 Kg (70 lb). Use two people to lift the unit. $ Caution - Electrostatic sensitive device Take precautions to protect against equipment damage due to electrostatic discharge (ESD). ------------------------------------------------------------ xi Part I ------------------------------------------------------------ Install Part I contains overview information and instructions for installing the GIGAswitch System: · Chapter 1 describes the GIGAswitch System and its component modules. · Chapter 2 describes the procedures that you must complete prior to installing the GIGAswitch System. These procedures include verifying the site preparation, unpacking the system, testing the system modules, installing the lower plenum in the rack, setting up electrostatic discharge (ESD) protection, and removing the modules. · Chapter 3 describes the procedures for installing the GIGAswitch System. These procedures include lifting the empty GIGAswitch System onto the lower plenum, attaching the GIGAswitch System to the rack, installing the upper plenum, and installing the modules. 1 ------------------------------------------------------------ Overview of the GIGAswitch System Chapter Contents This chapter introduces you to the GIGAswitch System and its component modules including: · Purpose of the GIGAswitch System · Parts of the GIGAswitch System · Location of the modules · Description of the logic modules · Description of the cooling and power modules Overview of the GIGAswitch System 1-1 Purpose of the GIGAswitch System ------------------------------------------------------------ Purpose of the GIGAswitch System General Description The GIGAswitch System is a standalone, intelligent, switching system that forwards packets among a set of connected data links. The data links can be connected to end stations, bridges, routers, and to other GIGAswitch Systems. The core of the GIGAswitch System is a crossbar switch (CBS) card that forms point-to-point communication paths by mapping inputs to outputs. The GIGAswitch System acts as a multiport FDDI bridge with all attached local area networks (LANs) being bridged together. Subsequently, added line cards will have their data links automatically added to the bridged LANS. Versions Two versions of the GIGAswitch System are available. The DEFGA-BA version is compatible with the US power requirements. The DEFGA-BB version in conjunction with a selected country kit is compatible with the power requirements for the selected country. See Appendix A for a listing of the power cord types found in country kits. Functions Both versions (DEFGA-Bx) function as a modular, multiport, FDDI bridge that uses the CBS card as the interconnection mechanism for its line cards and processing engines. The DEFGA-Bx utilizes both distributed and centralized packet processing algorithms to perform the following ANSI and IEEE 802.1d bridging functions: · Forwarding · Filtering · Learning · Aging · Spanning tree 1-2 Overview of the GIGAswitch System Parts of the GIGAswitch System ------------------------------------------------------------ Parts of the GIGAswitch System ------------------------------------------------------------ Part (Order Number) Quantity DEFGB-BA DEFGA-BB Option ------------------------------------------------------------ 2-port FDDI line card (DEFGL-AA) (contains one or more of the following types of PMD daughter cards 1 ): · MMF ANSI MIC PMD (DEFXM-AA) 2 · SMF PMD (DEFXS-AA) 3 1 1 Up to 11 Switch control processor (SCP) card 1 1 1 (DEFGP-AA) Crossbar switch (CBS) card (54-22116-01) 1 1 0 Clock card (54-22120-01) 1 1 0 Chassis (contains): · Fan tray assembly (70-30578-01) 4 · Logic backplane (54-21849-01) · Power backplane (54-22138-01) 1 1 0 Front end unit (FEU) (DEFGB-AA) 1 0 1 Front end unit (FEU) (DEFGB-AB) 0 1 1 Power status assembly (PSA) (70-30585-01) (contains): · Power system controller (PSC) card (54-22132-01) 1 1 0 Power cord (U.S.) (17-00083-42) 1 0 0 Power cord (Non-U.S.) 0 0 1 country kit per FEU ------------------------------------------------------------ 1 PMD daughter cards ordered separately as options (Maximum of 4 PMD daughter cards per line card) 2 MMF=multimode fiber, ANSI=American National Standards Institute, MIC=medium interface connector, and PMD=physical medium dependent. 3 SMF=single-mode fiber, and PMD=physical medium dependent. 4 Two per chassis ------------------------------------------------------------ Overview of the GIGAswitch System 1-3 Parts of the GIGAswitch System Configuration Used in This Document The configuration used in this document is a DEFGA-Bx. The upper port of the line card is configured as a single-attachment station (SAS) port, and the lower port of the line card is configured as a dual-attachment station (DAS) port.§ Multimode fiber (MMF) ANSI MIC PMD daughter cards are installed in both ports of the line card. mk28176ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX Location of the Modules ------------------------------------------------------------ Location of the Modules mk28107eðTX 2ðTX 1ðTX ------------------------------------------------------------ Description of the Cooling and Power Modules ------------------------------------------------------------ Description of the Cooling and Power Modules mk28107dðTX ðTX 1ðTX 2ðTX 1ðTX 3ðTX 4ðTX Description of the Cooling and Power Modules LEDs, Controls, and Connectors on the Cooling and Power Modules mk28124ðTX 3ðTX ------------------------------------------------------------ 4ðTX ------------------------------------------------------------ 3ðTX 4ðTX ------------------------------------------------------------ 2ðTX 2ðTX ------------------------------------------------------------ 1ðTX 1ðTX Description of the Logic Modules ------------------------------------------------------------ Description of the Logic Modules mk28123ðTX ------------------------------------------------------------ 2ðTX 1ðTX ðTx 3ðTX 4ðTX Description of the Logic Modules LEDs, Controls, and Connectors on the Logic Modules mk28123aðTX ------------------------------------------------------------ ------------------------------------------------------------ 4ðTX 2ðTX 6ðTX 4ðTX 3ðTX 5ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ 7ðTX 2 ------------------------------------------------------------ Preparing to Install the System Chapter Contents This chapter describes the procedures that you must complete prior to installing the GIGAswitch System: 1. Verifying the site preparation 2. Unpacking the system 3. Testing the system modules 4. Preparing the rack 5. Setting up ESD protection 6. Removing the system modules Preparing to Install the System 2-1 Verifying the Site Preparation ------------------------------------------------------------ Verifying the Site Preparation Verify the following requirements are met prior to installing the GIGAswitch System: · Area · Cable plant · Rack space Area Appendix A provides the physical, electrical, and environmental specifications for the GIGAswitch System. Cable Plant The DECconnect System Requirements Evaluation Workbook contains checklists and additional references used to verify proper cable plant installation. 2-2 Preparing to Install the System Verifying the Site Preparation Rack A grounded rack 47.5 cm (19 in) wide with 90.0 cm (35.4 in) contiguous vertical space is required for the installation of the GIGAswitch System, the lower plenum, and the upper plenum. The template provided in the rackmount kit is 90.0 cm (35.4 in) long and can be used to verify the contiguous space. The spacing between the holes of the rack should comply with EIA/RETMA standard EIA 310B or one of the metric 25mm standards (EIA 310-D, IEEE 1301, or IEC-48D) (See the following figure). Unpacking the System ------------------------------------------------------------ Unpacking the System Time Required 15 minutes. Tools Required · Band cutter Procedures 1. Removing the packing material 2. Identifying the contents of the shipping container 3. Testing the modules 2-4 Preparing to Install the System Unpacking the System Removing the Packing Material ------------------------------------------------------------ Note ------------------------------------------------------------ DO NOT remove GIGAswitch System from the pallet. The pallet will serve as a temporary operational platform during system module testing. ------------------------------------------------------------ ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the banding ! and the shipping container ". ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 2 Cut the banding ! from the shipping container and the pallet using a band cutter. 3 Slide the shipping container " up and off the GIGAswitch System using two people. 4 Remove the packing material, the rack mount kit, and the accessory kit 5 Remove the shipping bag from the GIGAswitch System. ------------------------------------------------------------ Preparing to Install the System 2-5 Unpacking the System Identifying the Contents of Shipping Container ------------------------------------------------------------ ------------------------------------------------------------ 3ðTX Unpacking the System Identifying the Contents of the Rackmount Kit mk28156 ðTX 1ðTX 2ðTX 3ðTX 4ðTX C:\PROJECTS\SUNOMA\FINALS\FINAL56B.EPS Unpacking the System Identifying the Contents of the Accessory Kit 2ðTX 1ðTX mk28157 ðTX Testing the System Modules ------------------------------------------------------------ Testing the System Modules Time Required 5 minutes. Tools Required None Procedures 1. Applying power to the GIGAswitch System 2. Evaluating the results of the MST Preparing to Install the System 2-9 Testing the System Modules Applying Power to the GIGAswitch System Complete the following steps to apply power to the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the power switch, !, the power cord § " and the power connector #. ------------------------------------------------------------ §Some power cords are shipped separately in country kits ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL75A.EPS ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAK75C.EPS ------------------------------------------------------------ 1ðTX 2ðTX 3ðTX Testing the System Modules Removing Power from the GIGAswitch System Complete the following steps to remove the power from the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the power switch ! and the power connector " ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL75A.EPS ------------------------------------------------------------ 1ðTX 2ðTX Preparing the Rack ------------------------------------------------------------ Preparing the Rack Time Required 30 minutes. Tools Required · Number 2 cross-point screwdriver · Pencil Procedures 1. Installing the clip nuts 2. Installing the lower plenum Preparing to Install the System 2-13 Preparing the Rack Installing the Clip Nuts Procedures 1. Marking the position for the clip nuts 2. Attaching the clip nuts Marking the Position for the Clip Nuts ) ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the template ! and distinguish between the metric markings ", and the RETMA § markings #. 2 Locate the front rails $, and the rear rails %. ------------------------------------------------------------ §RETMA - Radio Electronics Television Manufacture's Association ------------------------------------------------------------ 2-14 Preparing to Install the System Preparing the Rack ------------------------------------------------------------ ------------------------------------------------------------ 3 Identify the area in the rack designated for the GIGAswitch System. 4 Position the template ! behind one of the front rails $. Match the markings on the template ! to the holes in rail using one of the following: · Metric markings " (open slot) for metric racks. · RETMA markings # (closed slot) for RETMA racks. If the whole template does not fit in the spaced reserved, move equipment, as necessary, to reserve the additional space. 5 Mark the position on the front rail $ for the two clip nuts associated with the lower plenum and the six clip nuts associated with the GIGAswitch System. 6 Repeat steps 4 through 5 for the other front rail $. 7 Repeat step 4 for a rear rail %. 8 Mark the position on the inside of the rear rail % for the clip nut associated with the lower plenum bracket. 9 Repeat steps 7 and 8 for the other rear rail %. ------------------------------------------------------------ Preparing to Install the System 2-15 Preparing the Rack Attaching the Clip Nuts Complete the following steps to attach the clip nuts to the front and rear rails of the rack: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the clip nuts !, and the marked holes " on the rack. ------------------------------------------------------------ mk28148ðTX 2ðTX 1ðTX Preparing the Rack Installing the Lower Plenum Procedures 1. Attaching the lower plenum brackets 2. Attaching the lower plenum Preparing to Install the System 2-17 Preparing the Rack Attaching the Lower Plenum Bracket Complete the following steps to attach the lower plenum bracket to the rear rails of the rack: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate hole and the attached pin on the rear of the lower plenum brackets !, rear rails ", two screws # used to attach the lower plenum brackets to the rear rails of the rack, and the clip nuts (not shown) on the rear rails of the rack. ------------------------------------------------------------ mk28167ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL67.EPSðTx Preparing the Rack Attaching the Lower Plenum Complete the following steps to attach the lower plenum to the rack and to the lower plenum brackets: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the lower plenum !, the four clip nuts and associated screws ", the right and left lower plenum bracket #, the two screws $ used to connect the right and left lower plenum brackets to the lower plenum ------------------------------------------------------------ mk28168ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 4ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL68.EPS ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 2ðTX Setting Up ESD Protection ------------------------------------------------------------ Setting Up ESD Protection Protect the logic module against damage from electrostatic discharge (ESD) by using: · Static-free containers for long-term storage. · Grounded ESD wrist strap while installing and removing modules. · Grounded ESD mat for tempory storage. Using ESD Equipment The Portable Static-Dissipative Field Service Kit (Part No. 29-26246) is used to protect ESD sensitive modules against damage. Complete the following steps to set up and maintain a static-free area. ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Ground the unit. The unit is grounded through the power cord when it is connected between the unit and the primary power source. 2 Lay out the static-dissipative work surface (ESD mat) on a flat surface. 3 Connect the ground cord assembly to the ESD mat and to an unpainted surface on the unit. 4 Wear the ESD wrist strap and attach it to the ground cord assembly. ------------------------------------------------------------ 2-20 Preparing to Install the System Removing the System Modules ------------------------------------------------------------ Removing the System Modules ------------------------------------------------------------ Warning ------------------------------------------------------------ Remove all system modules from the unit to make it light enough for two people to lift the unit. ------------------------------------------------------------ ------------------------------------------------------------ Caution ------------------------------------------------------------ Ensure the power cord is connected at both ends to place the chassis at earth ground potential. ------------------------------------------------------------ Procedures 1. Removing the logic modules 2. Installing the PMD Daughter Cards 3. Removing the fan tray assemblies 4. Removing the cooling and power moduless Preparing to Install the System 2-21 Removing the System Modules Removing the Logic Modules ------------------------------------------------------------ Warning ------------------------------------------------------------ Remove all system modules from the unit to make it light enough for two people to lift the unit. ------------------------------------------------------------ ------------------------------------------------------------ Note ------------------------------------------------------------ The SCP card shown in the figure represents any logic module since all logic modules are removed in the same manner ------------------------------------------------------------ ------------------------------------------------------------ Note ------------------------------------------------------------ Remove the line card last to make it accessable for PMD daughter card installation. ------------------------------------------------------------ Complete the following steps to remove the logic modules from the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the two screws ! that fasten the selected module " to the GIGAswitch System and the ejectors # used to seat the module. ------------------------------------------------------------ mkv-0281-27ðTx 1ðTx 1ðTx ------------------------------------------------------------ 2ðTx 3ðTx 3ðTx ------------------------------------------------------------ Removing the System Modules ------------------------------------------------------------ ------------------------------------------------------------ 1 Set up the ESD equipment. 2 Slip on ESD wrist band. 3 Loosen the upper and lower screws !. 4 Move the ejectors # outward to unseat the module " from the unit. 5 GENTLY slide the module " out of the unit. 6 Place module " in a static proof bag. 7 Place bagged module " on a flat surface or on another bagged module. The modules can be stacked four modules high. 8 Repeat steps 3 through 6 to remove the rest of the logic modules. ------------------------------------------------------------ Preparing to Install the System 2-23 Installing the PMD Daughter Cards ------------------------------------------------------------ Installing the PMD Daughter Cards The following table provides the part numbers for the possible PMD daughter cards: ------------------------------------------------------------ Physical Media PMD Part Number ------------------------------------------------------------ ANSI Multimode Fiber FDDI DEFXM-AA Single-mode Fiber FDDI DEFXS-AA ------------------------------------------------------------ Preparing to Install the System 2-25 Installing the MMF ANSI MIC PMD ------------------------------------------------------------ Installing the MMF ANSI MIC PMD Unpacking the PMD ------------------------------------------------------------ Note ------------------------------------------------------------ (The extra posts and the PHY M key provided in the package are not used in this installation. The PHY A and PHY B keys are used in the DAS configuration of the ANSI Multimode Fiber FDDI PMD only. ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 1 Set up the ESD equipment. 2 Slip on ESD wrist band. 3 Unpack the PMD and check the contents against the packing slip. ------------------------------------------------------------ 2-26 Preparing to Install the System Installing the MMF ANSI MIC PMD Installing a PHY Port Key ------------------------------------------------------------ Note ------------------------------------------------------------ This section applies to a dual-attachment station (DAS) configuration only ------------------------------------------------------------ The connector on the PMD daughter card is shipped with a universal (PHY S) key installed. The PHY S key is replaced by a PHY A key for the PMD daughter card designated for the top slot. The PHY S key is replaced by a PHY B key for the PMD daughter card designated for the bottom slot. Complete the following procedure to replace the PHY keys: Installing the MMF ANSI MIC PMD Mounting the MMF ANSI MIC PMD Complete the following steps to install multimode fiber (MMF) ANSI MIC PMD: daughter cards. ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Identify the ESD mat !, port slot ", the two retaining clips #, the PMD daughter card $, the brass standoffs %, the bezel &, and the collar shroud '. ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 2 Slip on ESD wrist strap and place the line card on the ESD mat ! with the components of the line card facing up and the top of the line card facing left. ------------------------------------------------------------ Note ------------------------------------------------------------ Remove the top blank bezel for a SAS configuration. Remove both the top and the bottom blank bezel for a DAS configuration. ------------------------------------------------------------ 2-28 Preparing to Install the System Installing the MMF ANSI MIC PMD ------------------------------------------------------------ ------------------------------------------------------------ 3 Remove the blank bezel. Release the locking tabs on both sides of the bezel using a screwdriver. 4 Insert the collar shroud ' into the port slot " in the handle of the line card. Orient the open portion of the U shaped collar shroud ' in the up position and insert the collar shroud into the port slot " in the handle of the line card. Slide the collar shroud into the port slot " in the handle of the line card until the fingers of the collar shroud rest against the handle of the line card. 5 Mount the PMD daughter card $ containing the PHY S key or the PHY A key in the upper slot of the selected port. Orient the PMD daughter card with the connector facing down and away from the handle of the line card and position the PMD daughter card over the line card. Place the collar shroud ' around the front of the PMD daughter card. Snap the PMD daughter card onto the two brass standoffs % mounted on the line card, and then mate the connector by pressing down on the back of the PMD daughter card. ------------------------------------------------------------ Note ------------------------------------------------------------ Ensure the bezel completely surrounds the collar shroud before snapping the bezel onto the front of the handle of the line card. ------------------------------------------------------------ 6 Snap the bezel & onto the front of the handle of the line card. Orient the bezel & with the label area facing the top of the line card. 7 This step is for DAS configuration only. Repeat steps 4 through 6 to install the PMD daughter card containing the PHY B key in the lower slot of the selected port. 8 Place line card in a static proof bag. 9 Place bagged module on a flat surface or on another bagged module. The modules can be stacked four modules high. ------------------------------------------------------------ Preparing to Install the System 2-29 Installing the SMF PMD ------------------------------------------------------------ Installing the SMF PMD Unpacking the PMD ------------------------------------------------------------ Note ------------------------------------------------------------ (The extra posts are not used in this installation ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 1 Set up the ESD equipment. 2 Slip on ESD wrist band. 3 Unpack the PMD and check the contents against the packing slip. 4 Remove the cable-ties from the coiled cable bundle. ------------------------------------------------------------ Preparing to Install the System 2-31 Installing the SMF PMD Prepairing the SMF PMD Complete the following steps to prepare single-mode fiber (SMF) PMD (DEFXS-AA) daughter cards: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Identify the receiver cable !, the transceiver cable ", the bezel #, the coiled cable bundle $, the coiled cable tie point %, the lower port cable-tie anchor mounting location &, and the upper port cable-tie anchor mounting location '. ------------------------------------------------------------ MKV-0281-99ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ 4ðTX ------------------------------------------------------------ 6ðTX ------------------------------------------------------------ 7ðTX ------------------------------------------------------------ 5ðTX Installing the SMF PMD ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Note ------------------------------------------------------------ The receiver cable is the thin white cable. The transceiver cable is the thick yellow cable ------------------------------------------------------------ 4 Mate the connectors of the receiver cable ! and the transceiver cable " to the respective connectors on the bezel #. Orient the bezel # with the label area facing the top of the line card. Extend the loose ends of the receiver cable ! and the transceiver cable " through the hole in the line card. The receiver cable ! will be to the left and the transceiver cable " will be to the right. ------------------------------------------------------------ Caution ------------------------------------------------------------ Do not exceed the 3" minimum bend diameter when adjusting coils. ------------------------------------------------------------ 5 Roughly dress the coiled cable bundle $. Equalize the cables in the coiled cable bundle and dress the coiled cable bundle to the rear of the PMD daughter card as shown in the figure. ------------------------------------------------------------ Note ------------------------------------------------------------ Loosely install the cable-ties to allow for final dressing of the loops. ------------------------------------------------------------ 6 Install the cable-ties. Wrap one cable-tie around all the cables in the coiled cable bundle $ and attach it to the PMD daughter card using the after post hole on the TX side of the PMD daughter card. Wrap the other cable-tie around all the cables in the coiled cable bundle $ and position it near the RX connector. ------------------------------------------------------------ Preparing to Install the System 2-33 Installing the SMF PMD Mounting the SMF PMD Complete the following steps to mount the single-mode fiber (SMF) PMD (DEFXS-AA) daughter cards: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Identify the receiver cable !, the transceiver cable ", the bezel #, the coiled cable bundle $, the coiled cable tie point %, the lower port cable-tie anchor mounting location &, and the upper port cable-tie anchor mounting location '. ------------------------------------------------------------ MKV-0281-99ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ 4ðTX ------------------------------------------------------------ 6ðTX ------------------------------------------------------------ 7ðTX ------------------------------------------------------------ 5ðTX Installing the SMF PMD 3 Mate the connector by pressing down on the back of the PMD daughter card. 4 Snap the bezel # onto the front of the handle of the line card. Orient the bezel # with the label area facing the top of the line card. 5 Dress the cables in the coiled cable bundle and tighten the cable-ties. 6 Install final cable_tie. If SMF PMD daughter card is already installed in the port, attach the two coiled cable bundles together at the tie point % shown using a cable- tie. If this is the first SMF PMD daughter card to be installed, mount the cable-tie anchor in the appropriate position (the position for the upper port ' or the position for the lower port &), and attach the coiled cable bundle $ to the appropriate cable-tie anchor. 7 This step is for DAS configuration only. Repeat steps 4 through 6 to install the other PMD daughter card. 8 Place line card in a static proof bag. 9 Place bagged module on a flat surface or on another bagged module. The modules can be stacked four modules high. ------------------------------------------------------------ Preparing to Install the System 2-35 Installing the SMF PMD Removing the Fan Tray Assemblies ------------------------------------------------------------ Warning ------------------------------------------------------------ Remove all system modules from the unit to make it light enough for two people to lift the unit. ------------------------------------------------------------ Complete the following steps to remove the fan tray assemblies from the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the two fasteners ! that attach the selected fan tray assembly " to the GIGAswitch System, and the handle #. ------------------------------------------------------------ mk28152ðTX 1ðTX 3ðTX 2ðTX ------------------------------------------------------------ ------------------------------------------------------------ Installing the SMF PMD ------------------------------------------------------------ Warning ------------------------------------------------------------ Remove all system modules from the unit to make it light enough for two people to lift the unit. ------------------------------------------------------------ Removing the PSA Complete the following steps to remove the power status assembly (PSA). ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the four screws ! that fasten the module to the GIGAswitch System, the handle " of the module, and the slot # designated for the module. ------------------------------------------------------------ ------------------------------------------------------------ mk28169ðTX 3ðTX 2ðTX ------------------------------------------------------------ ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ Installing the SMF PMD ------------------------------------------------------------ Warning ------------------------------------------------------------ Remove all system modules from the unit to make it light enough for two people to lift the unit. ------------------------------------------------------------ ------------------------------------------------------------ Caution ------------------------------------------------------------ Remove FEU after removing all logic modules. The power cord provides the ground required for ESD protection. ------------------------------------------------------------ Removing the FEU Complete these steps to remove a front end unit (FEU). ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the power switch !, the power cord ", the four screws # that fasten the selected module to the GIGAswitch System, and the handle $ of the selected module. ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL75A.EPS ------------------------------------------------------------ 1ðTX 2ðTX 3ðTX 4ðTX ------------------------------------------------------------ Installing the SMF PMD ------------------------------------------------------------ ------------------------------------------------------------ 2 Place the power switch ! in the O (OFF) position and remove the power cord " from the primary power outlet and the power connector. 3 Remove the four screws # on the module using a number 2 cross-point screwdriver. 4 Slide the module out of the unit. Grasp the handle $ with one hand and support the bottom of the module with your other hand. 5 Repeat steps 1 through 4 to remove the other module if installed. ------------------------------------------------------------ What is Next? Now that you have removed all of the system modules you are now ready to lift the empty GIGAswitch System onto the lower plenum. Continue to the next chapter. Preparing to Install the System 2-39 3 ------------------------------------------------------------ Installing the GIGAswitch System ------------------------------------------------------------ Note ------------------------------------------------------------ Complete the procedures described in Chapter 2 before proceeding with this chapter. ------------------------------------------------------------ Chapter Contents This chapter describes the procedures for installing the empty GIGAswitch System including: 1. Installing the GIGAswitch System in the rack 2. Attaching the upper plenum to the GIGAswitch System 3. Installing the system modules Installing the GIGAswitch System 3-1 Installing the GIGAswitch System in the Rack ------------------------------------------------------------ Installing the GIGAswitch System in the Rack Time Required 45 minutes. Needed Tools · Adjustable wrench · Number 2 cross-point screwdriver · ESD equipment Procedures 1. Removing the GIGAswitch System from the pallet 2. Placing the GIGAswitch System on the lower plenum 3. Attaching the GIGAswitch System to the rack Installing the GIGAswitch System 3-3 Installing the GIGAswitch System in the Rack Removing the GIGAswitch System from the Pallet ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the four screws ! attaching the brackets to the pallet, and the six screws " attaching the brackets to the GIGAswitch System. ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 1ðTX 2ðTX ------------------------------------------------------------ Installing the GIGAswitch System in the Rack Placing the GIGAswitch System on the Lower Plenum ------------------------------------------------------------ Warning ------------------------------------------------------------ The empty GIGAswitch System weighs 31.75 kg (70 lbs). Use two people to lift the unit. ------------------------------------------------------------ ------------------------------------------------------------ 1ðTx ------------------------------------------------------------ Installing the GIGAswitch System in the Rack Attaching the GIGAswitch System to the Rack ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the GIGAswitch System !, the 12 clip nuts (not shown) designated for the GIGAswitch System, and the 12 screws ". ------------------------------------------------------------ mk28162 ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 2ðTX Attaching the Upper Plenum to the GIGAswitch System ------------------------------------------------------------ Attaching the Upper Plenum to the GIGAswitch System ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the upper plenum !, the four shoulder screws ", and the mounting screw #. ------------------------------------------------------------ ------------------------------------------------------------ 2ðTx Installing the System Modules ------------------------------------------------------------ Installing the System Modules Procedures 1. Installing the FEUs 2. Installing the PSA 3. Installing the fan tray assemblies 4. Installing the logic modules Installing the GIGAswitch System 3-9 Installing the System Modules ------------------------------------------------------------ Caution ------------------------------------------------------------ Install the FEU before installing any logic modules. The power cord provides the ground required for ESD protection. ------------------------------------------------------------ Installing the FEU ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the power switch !, the power cord ", the four screws # that fasten the selected module to the GIGAswitch System, and the handle $ of the selected module. ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL75A.EPS ------------------------------------------------------------ 1ðTX 2ðTX 3ðTX 4ðTX ------------------------------------------------------------ Installing the System Modules Installing the PSA ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the four screws ! that fasten the module to the GIGAswitch System, the handle " of the module, and the slot # designated for the module. ------------------------------------------------------------ ------------------------------------------------------------ mk28169ðTX 3ðTX 2ðTX ------------------------------------------------------------ ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ Installing the System Modules Installing the Fan Tray Assemblies ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the two fasteners ! that attach the selected fan tray assembly " to the GIGAswitch System, and the handle # of the selected fan tray assembly. ------------------------------------------------------------ mk28152ðTX 1ðTX 3ðTX 2ðTX ------------------------------------------------------------ ------------------------------------------------------------ Installing the System Modules Installing the Logic Module ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the screws ! that fasten the selected module " to the GIGAswitch System and the ejectors # used to seat the module. ------------------------------------------------------------ mkv-0281-27ðTx 1ðTx 1ðTx ------------------------------------------------------------ 2ðTx 3ðTx 3ðTx ------------------------------------------------------------ Part II ------------------------------------------------------------ Test Part II contains information for testing the GIGAswitch System: · Chapter 4 describes the procedures that you must complete before testing the GIGAswitch System. These procedures include preparing the ports, connecting the Out-of-Band Management (OBM) terminal, and setting the security switch. · Chapter 5 describes the procedures for initiating the MSTs and provides instructions for evaluating the results of the MSTs. 4 ------------------------------------------------------------ Preparing to Test the System Chapter Contents This chapter describes the following procedures that should be completed prior to conducting tests on the GIGAswitch System: 1. Connecting the OBM terminal 2. Setting the security switch Preparing to Test the System 4-1 Connecting the OBM terminal ------------------------------------------------------------ Connecting the OBM terminal Complete the following steps to connect an out-of-band management (OBM) terminal to the OBM port on the clock card: 1 ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the OBM port !, the OBM terminal #, the modem $, remote modem %, remote OBM terminal ', and the associated cables ", & § ------------------------------------------------------------ §Typical part numbers BC22D-xx, and BC05D-xx respecively where xx = length of cable in feet. ------------------------------------------------------------ mk28151ðTX ------------------------------------------------------------ 1ðTX 2ðTX 3ðTX ------------------------------------------------------------ ------------------------------------------------------------ 5ðTX 4ðTX 7ðTX ------------------------------------------------------------ 6ðTX Connecting the OBM terminal ------------------------------------------------------------ ------------------------------------------------------------ 2 Connect an RS232 cable " to the terminal # and to the OBM port !. 3 Install a modem $ as described in the appropriate modem documentation and connect the modem $ to the OBM terminal # +. 4 Have the remote modem %, and the remote OBM terminal ' installed at the remote site +. 5 Refer to the terminal documentation and set up the terminal as follows. 9600 baud rate 8 bits no parity 1 stop bit 6 Press ------------------------------------------------------------ ------------------------------------------------------------ Return ------------------------------------------------------------ ------------------------------------------------------------ or ------------------------------------------------------------ ------------------------------------------------------------ Ctrl/O ------------------------------------------------------------ ------------------------------------------------------------ to prepare the terminal for out-of-band commands. 7 Set the security switch position 4 to allow OBM access without password. ------------------------------------------------------------ +Modem installation only ------------------------------------------------------------ Preparing to Test the System 4-3 Setting the Security Switch ------------------------------------------------------------ Setting the Security Switch The security switch controls the ability to configure or monitor the GIGAswitch System using in-band § or out-of-band (OBM) + management commands. The following figure and table identify the security switch and the positions of the security switch. mk28109aðTX J:\SOURCE\ART\NEWART\FINAL09B.EPS ------------------------------------------------------------ 5 ------------------------------------------------------------ Testing the System Chapter Contents This chapter describes the various screens associated with the diagnostics mode and the following procedures: 1. Initiating the MST 2. Evaluating the results of the MST Testing the System 5-1 Diagnostic Mode Screens ------------------------------------------------------------ Diagnostic Mode Screens The following figures show the various screens available in diagnostic mode and their interconnection. 5-2 Testing the System Diagnostic Mode Screens Testing the System 5-3 Help Screens ------------------------------------------------------------ Help Screens The following figures describe the commands available in the diagnostic dispatcher and the terminal protocol modes. 5-4 Testing the System Initiating the MST ------------------------------------------------------------ Initiating the MST The following methods are used to initiate the module self-test (MST). · Applying power to the GIGAswitch System · Rebooting the GIGAswitch System · Running MST in diagnostic mode Testing the System 5-5 Initiating the MST Applying Power to the GIGAswitch System Complete the following steps to apply power to the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the power switch, !, the power cord § " and the power connector #. ------------------------------------------------------------ §Some power cords are shipped separately in country kits ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL75A.EPS ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAK75C.EPS ------------------------------------------------------------ 1ðTX 2ðTX 3ðTX Initiating the MST Rebooting the GIGAswitch System The following contains the displays and selections required to reboot the GIGAswitch System from the OBM terminal. To initiate an OBM session apply power to the OBM terminal or press ------------------------------------------------------------ ------------------------------------------------------------ ctrl-O ------------------------------------------------------------ ------------------------------------------------------------ .§ ------------------------------------------------------------ Action Results ------------------------------------------------------------ Look for operational firmware prompt CLK i Type ------------------------------------------------------------ ------------------------------------------------------------ Ctrl/O ------------------------------------------------------------ ------------------------------------------------------------ Main Menu appears§ Type 2 to select Show /Modify GIGAswitch Configuration Configuration Menu appears Type 6 to select Reset Management/Reboot the GIGAswitch Reset/Reboot Menu appears Type 2 to select Reboot the GIGAswitch WARNING: . . . (yes/no) appears Type yes Reboot Menu appears Type 1 to select Normal Reboot CLKi appears ------------------------------------------------------------ §If an error message appears, set the security switch to position 4 and try again. ------------------------------------------------------------ ------------------------------------------------------------ § If power has already been applied the Main Menu will be present. Testing the System 5-7 Initiating the MST Running the MST in Diagnostic Mode The following methods are used to enter diagnostic mode: · Rebooting into diagnostic mode - preferred · Installing the maintenance jumper - alternate Rebooting into Diagnostic Mode The following contains the displays and selections required to reboot the GIGAswitch System from the OBM terminal into diagnostic mode. To initiate an OBM session apply power to the OBM terminal or press ------------------------------------------------------------ ------------------------------------------------------------ ctrl-O ------------------------------------------------------------ ------------------------------------------------------------ .§ ------------------------------------------------------------ Action Results ------------------------------------------------------------ Look for operational firmware prompt CLK i CLKi appears Type Ctrl/O Main Menu appears Type 2 to select Show /Modify GIGAswitch Configuration Configuration Menu appears Type 6 to select Reset Management/ Reboot the GIGAswitch Reset/Reboot Menu appears Type 2 to select Reboot the GIGAswitch WARNING: . . . (yes/no) appears Type yes Reboot Menu appears Type 2 to select Reboot into diagnostic mode CLK diagnostic dispatcher menu and prompt appears ------------------------------------------------------------ ------------------------------------------------------------ § If power has already been applied the Main Menu will be present. Testing the System 5-9 Initiating the MST Installing the Maintenance Jumper An SCP card must be operational to enter an OBM mode of operation. Using a maintenance jumper allows entry into the OBM maintenance mode without an operational SCP. The following figure and table describe how to enter the OBM maintenance mode using a maintenance jumper. ------------------------------------------------------------ Number Description ------------------------------------------------------------ ! Slot 6 " Maintenance jumper # Slot 7 ------------------------------------------------------------ 5-10 Testing the System Initiating the MST ------------------------------------------------------------ Action Results ------------------------------------------------------------ Primary power switch placed in O position Power removed from unit Access the maintenance connector Cards removed from slots 6 and 7 Install maintenance jumper Jumper installed as shown Install cards in slots 6 and 7 Cards reinstalled Primary power switch placed in the (1)(ON) position CLK diagnostic dispatcher menu and prompt appears ------------------------------------------------------------ Testing the System 5-11 Testing Procedures ------------------------------------------------------------ Testing Procedures Module self-tests (MSTs) are initiated when power is applied or when the system is rebooted. See MST summary to interpret the results of the MSTs. The diagnostic mode can be used to run selected tests multiple times to isolate intermittent faults. (See example on the next page). When the fault is identified Repeat the MSTs to ensure that all faults have been corrected. Example of Using Diagnostic Mode The following figure is an example of using the diagnostic mode to isolate an intermittent fault in the clock module. Complete navigational information for the diagnostic mode is also provided. For a list of available tests for a given module type "li" at the Diagnostic Dispatcher prompt. Description of Example After rebooting into diagnostic mode and entering the CLK Diagnostic Dispatcher mode the following line was entered to set the number of passes from 1 to 10 and to inhibit all outputs except the summaries. Since the module will be replaced if any test fails, it is not necessary to see the other displays. After setting the default switches, test 101 was run 10 times. The summary indicates the results of the test. A line card or an SCP card can be tested using the same commands once the Diagnostic Dispatcher mode for that card is entered. 5-12 Testing the System Testing Procedures Testing the System 5-13 Meaning of LEDs ------------------------------------------------------------ Meaning of LEDs This section identifies each LED on the logic module and describes its purpose: · Line card · SCP card · Clock card · CBS card Line Card LEDs mk28108ðTX ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL08A.EPS ------------------------------------------------------------ 4ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ ------------------------------------------------------------ Meaning of LEDs SCP Card LEDs and Control mk28110ðTX J:\SOURCE\ART\NEWART\FINAL10A.EPS ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 2ðTX 1ðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ ------------------------------------------------------------ Meaning of LEDs SCP HEX LED Table The following table further identifies the purpose of the SCP LEDs. ------------------------------------------------------------ Number/Event LED ! Condition HEX LED " Condition Meaning ------------------------------------------------------------ 1/SCP card startup Amber Out MST has not passed. 2/Startup complete Solid amber LED F Startup complete 3/SCP card MST Flashing amber Test number updated MST in progress Solid green B MST passed, SCP card in backup mode Solid amber or out Solid number MST failed 4/SCP election Solid green E Elected switch control processor Solid green Test passed Solid amber Test failed 5/Downline load Solid green D New firmware images are being loaded into the flash memory during a firmware upgrade. Solid green Alternating D/E Corrupt image detected during system boot. SCP continues to try to retrieve a good image from the bootserver. ------------------------------------------------------------ Testing the System 5-17 Meaning of LEDs Clock Card LEDs J:\SOURCE\ART\NEWART\FINAL32B.EPS ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Meaning of LEDs CBS LEDs mk28133ðTX ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL33A.EPS ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Meaning of LEDs Logic Module LED Summary The following figures and tables identify each indicator and the meaning of its various conditions. mk28123bðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ 6ðTX ------------------------------------------------------------ 5ðTX ------------------------------------------------------------ 7ðTX ------------------------------------------------------------ 4ðTX 2ðTX 1ðTX ------------------------------------------------------------ 4ðTX Meaning of LEDs ------------------------------------------------------------ Number/Name Condition ------------------------------------------------------------ !/PMD FRU Off = PMD OK and fully operational or no power Steady amber = PMD loop test failure (defective PMD FRU) "/PMD PHY Off = no power. Steady amber = Link confidence test (LCT) failure Flashing amber = Topology reject Steady green = Connection accepted Flashing green = Awaiting a connection Flashing amber/green = Stand by (dual-homing) #/Line card Off = No power or with port LEDs off and PMD daughter card LEDs on, card is not fully seated or in process of being removed. Steady amber = MST failure or fatal firmware error. Flashing amber = MST in progress (Wait). Steady green = MST passed. Flashing green = Firmware down-line load (DLL) in progress - will flash at 1/2 second intervals. Flashing amber/green = Non-fatal firmware error. $/Port Off = No power or with port LEDs off and PMD daughter card LEDs on, card is not fully seated or in process of being removed. Steady amber = MST failure in this port Flashing amber = MST in progress (wait) Steady green = MST passed, port active and in forwarding state. Flashing green = MST passed, port in backup , preforwarding state, or station management is off. %/SCP card Off = No power or severe fault Steady amber = MST failure Flashing amber = MST in progress (Wait) Steady green with B or E in HEX LED = MST passed Steady green with D in HEX LED = Downline load in progress Steady green with alternating D/E in HEX LED = Corrupt image detected during downline load. Retrying &/Clock card Steady amber = MST failure Flashing amber = MST in progress Steady green = MST passed '/CBS card Steady amber = MST failure Flashing amber = MST in progress Steady green = MST passed ------------------------------------------------------------ Testing the System 5-21 Meaning of LEDs Cooling and Power Modules LED Summary mk28124aðTX 3ðTX ------------------------------------------------------------ 2ðTX 1ðTX 4ðTX 6ðTX 5ðTX ------------------------------------------------------------ 3ðTX 2ðTX 1ðTX 4ðTX 6ðTX 5ðTX Part III ------------------------------------------------------------ Service Part III contains information for replacing the field replaceable units (FRUs) · Chapter 6 describes the procedures you must complete before replacing the GIGAswitch System modules. Failure to perform these procedures can result in harm to personnel or equipment. These procedures include setting up electrostatic discharge (ESD) protection, evaluating the need for power removal, and for applying power. · Chapter 7 describes the procedures for replacing the cooling and power modules and the logic modules. Cooling and power modules include modules of the fan tray assembly, front end unit (FEU), power status assembly (PSA) , and power system controller (PSC) families. Logic modules include modules of the line card, physical medium dependent (PMD) daughter card, switch control processor (SCP), clock card, and crossbar switch (CBS) families. · Chapter 8 describes the procedures for removing the GIGAswitch System. · Chapter 9 describes the procedures for replacing the logic and power backplanes after all the modules have been removed from the selected backplane. 6 ------------------------------------------------------------ Preparing to Replace Modules Chapter Contents This chapter lists the prerequisites for replacing the GIGAswitch System modules and describes the following procedures: · Setting up ESD protection · Removing power from the system Preparing to Replace Modules 6-1 Prerequisites for Replacing GIGAswitch System Modules ------------------------------------------------------------ Prerequisites for Replacing GIGAswitch System Modules GIGAswitch System modules include the following: · Logic modules · Cooling and power modules Logic Modules The following figure and associated table summarize the prerequisites for removing logic modules. They identify slot limitations, which modules must be removed prior to performing the replacement procedure for the desired module, and whether or not power must be removed or ESD equipment used. mk28123ðTX ------------------------------------------------------------ 2ðTX 1ðTX ðTx 3ðTX 4ðTX Setting Up ESD Protection ------------------------------------------------------------ Setting Up ESD Protection Protect the logic module against damage from electrostatic discharge (ESD) by using: · Static-free containers for long-term storage. · Grounded ESD wrist strap while installing and removing modules. · Grounded ESD mat for tempory storage. Using ESD Equipment The Portable Static-Dissipative Field Service Kit (Part No. 29-26246) is used to protect ESD sensitive modules against damage. Complete the following steps to set up and maintain a static-free area. ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Ground the unit. The unit is grounded through the power cord when it is connected between the unit and the primary power source. 2 Lay out the static-dissipative work surface (ESD mat) on a flat surface. 3 Connect the ground cord assembly to the ESD mat and to an unpainted surface on the unit. 4 Wear the ESD wrist strap and attach it to the ground cord assembly. ------------------------------------------------------------ Preparing to Replace Modules 6-3 Removing Power ------------------------------------------------------------ Removing Power Complete the following steps to remove the power from the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the power switch ! and the power connector " ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL75A.EPS ------------------------------------------------------------ 1ðTX 2ðTX 7 ------------------------------------------------------------ Replacing Modules ------------------------------------------------------------ Caution ------------------------------------------------------------ Read Chapter 6 before attempting to replace any module in the GIGAswitch System. ------------------------------------------------------------ Chapter Contents This chapter describes the following procedures for replacing the GIGAswitch System: · Replacing a logic module · Replacing a PMD daughter card · Replacing a blank handle · Replacing a fan tray assembly · Replacing a FEU · Replacing a power supply filler panel · Replacing a PSA · Replacing a PSC card Replacing Modules 7-1 Replacing a Logic Module ------------------------------------------------------------ Replacing a Logic Module ------------------------------------------------------------ Note ------------------------------------------------------------ Appendix D contains the recommended location for the modules. ------------------------------------------------------------ Complete the following steps to replace a logic module: 1. Remove power and set up the ESD equipment. See Chapter 6 §. 2. Wear the grounded ESD wrist band. 3. Unpack the replacement module. Leave the module in the ESD bag. 4. Place the ESD bagged replacement module on a flat surface. 5. Place the empty container on the ESD mat. 6. Remove the module to be replaced from the chassis. See the procedure in Removing the Logic Module. 7. Place the module to be replaced in the empty container. 8. Remove the replacement module from the ESD bag. 9. Install the replacement module in the chassis. See the procedure in Installing the Logic Module. 10. Remove the module to be replaced from the container and place it in the ESD bag. 11. Place the ESD bagged module in the container. 12. Remove the ESD wrist band. ------------------------------------------------------------ § The SCP card can be hotswapped 7-2 Replacing Modules Replacing a Logic Module Removing the Logic Module The following procedure describes how to remove the logic module. See Replacing a Logic Module for the complete replacement procedure: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the two screws ! that fasten the selected module " to the GIGAswitch System and the ejectors # used to seat the module. ------------------------------------------------------------ mkv-0281-27ðTx 1ðTx 1ðTx ------------------------------------------------------------ 2ðTx 3ðTx 3ðTx ------------------------------------------------------------ Replacing a Logic Module Installing the Logic Module The following procedure describes how to install the logic module. See Replacing a Logic Module for the complete replacement procedure: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the screws ! that fasten the selected module " to the GIGAswitch System and the ejectors # used to seat the module. ------------------------------------------------------------ mkv-0281-27ðTx 1ðTx 1ðTx ------------------------------------------------------------ 2ðTx 3ðTx 3ðTx ------------------------------------------------------------ Replacing the PMD Daughter Cards ------------------------------------------------------------ Replacing the PMD Daughter Cards The following table provides the part numbers for the possible PMD daughter cards: ------------------------------------------------------------ Physical Media PMD Part Number ------------------------------------------------------------ ANSI Multimode Fiber FDDI DEFXM-AA Single-mode Fiber FDDI DEFXS-AA ------------------------------------------------------------ Replacing Modules 7-5 Removing the MMF ANSI MIC PMD ------------------------------------------------------------ Removing the MMF ANSI MIC PMD Complete the following steps to remove the multimode fiber (MMF) ANSI MIC PMD: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Identify the ESD mat !, port slot ", the two retaining clips #, the PMD daughter card $, the brass standoffs %, the bezel &, and the collar shroud '. ------------------------------------------------------------ 7-6 Replacing Modules Removing the MMF ANSI MIC PMD ------------------------------------------------------------ ------------------------------------------------------------ 2 Remove the line card that will contain the new PMD daughter card from the unit. See Removing the Logic Module 3 Place the line card on the ESD mat ! with the components of the line card facing up and the top of the line card facing left. 4 Unsnap the bezel & from the front of the handle of the line card. Access the retaining clips from the back of the line card handle, release the retaining clips #, and separate the PMD blank cover from the line card. 5 Remove the collar shroud ' from the port slot " in the handle of the line card. 6 Remove the PMD daughter card $ from the line card. Mate the connector by lifting up on the back of the PMD daughter card, and then unsnap the PMD daughter card from the two brass standoffs % mounted on the line card. 7 Install new PMD daughter card or blank PMD cover. To install a blank PMD cover snap the PMD cover into the selected port slot. To install a new PMD daughter card see the appropriate installation procedure for the PMD daughter card concerned. 8 Install the line card in the unit. See Installing the Logic Module. ------------------------------------------------------------ Replacing Modules 7-7 Installing the MMF ANSI MIC PMD ------------------------------------------------------------ Installing the MMF ANSI MIC PMD Unpacking the PMD ------------------------------------------------------------ Note ------------------------------------------------------------ (The extra posts and the PHY M key provided in the package are not used in this installation. The PHY A and PHY B keys are used in the DAS configuration of the ANSI Multimode Fiber FDDI PMD only. ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 1 Set up the ESD equipment. 2 Slip on ESD wrist band. 3 Unpack the PMD and check the contents against the packing slip. ------------------------------------------------------------ Replacing Modules 7-9 Installing the MMF ANSI MIC PMD Mounting the MMF ANSI MIC PMD Complete the following steps to install multimode fiber (MMF) ANSI MIC PMD: daughter cards. ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Identify the ESD mat !, port slot ", the two retaining clips #, the PMD daughter card $, the brass standoffs %, the bezel &, and the collar shroud '. ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 2 Slip on ESD wrist strap and place the line card on the ESD mat ! with the components of the line card facing up and the top of the line card facing left. ------------------------------------------------------------ Note ------------------------------------------------------------ Remove the top blank bezel for a SAS configuration. Remove both the top and the bottom blank bezel for a DAS configuration. ------------------------------------------------------------ 7-10 Replacing Modules Installing the MMF ANSI MIC PMD ------------------------------------------------------------ ------------------------------------------------------------ 3 Remove the blank bezel. Release the locking tabs on both sides of the bezel using a screwdriver. 4 Insert the collar shroud ' into the port slot " in the handle of the line card. Orient the open portion of the U shaped collar shroud ' in the up position and insert the collar shroud into the port slot " in the handle of the line card. Slide the collar shroud into the port slot " in the handle of the line card until the fingers of the collar shroud rest against the handle of the line card. 5 Mount the PMD daughter card $ containing the PHY S key or the PHY A key in the upper slot of the selected port. Orient the PMD daughter card with the connector facing down and away from the handle of the line card and position the PMD daughter card over the line card. Place the collar shroud ' around the front of the PMD daughter card. Snap the PMD daughter card onto the two brass standoffs % mounted on the line card, and then mate the connector by pressing down on the back of the PMD daughter card. ------------------------------------------------------------ Note ------------------------------------------------------------ Ensure the bezel completely surrounds the collar shroud before snapping the bezel onto the front of the handle of the line card. ------------------------------------------------------------ 6 Snap the bezel & onto the front of the handle of the line card. Orient the bezel & with the label area facing the top of the line card. 7 This step is for DAS configuration only. Repeat steps 4 through 6 to install the PMD daughter card containing the PHY B key in the lower slot of the selected port. 8 Place line card in a static proof bag. 9 Place bagged module on a flat surface or on another bagged module. The modules can be stacked four modules high. ------------------------------------------------------------ Replacing Modules 7-11 Removing the SMF PMD Daughter Card ------------------------------------------------------------ Removing the SMF PMD Daughter Card Complete the following steps to remove the single-mode fiber (SMF) PMD (DEFXS-AA) daughter card: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Identify the ESD mat !, port slot ", the two retaining clips #, the PMD daughter card $, the brass standoffs %, the bezel&, the receiver cable ' and the transceiver cable (. ------------------------------------------------------------ 7-12 Replacing Modules Removing the SMF PMD Daughter Card ------------------------------------------------------------ ------------------------------------------------------------ 2 Remove the line card that will contain the new PMD daughter card from the unit. See Removing the Logic Module. 3 Place the line card on the ESD mat ! with the components of the line card facing up and the top of the line card facing left. 4 Cut the cable-tie that connects the coiled cable bundles the cable-tie anchor or to another PMD. 5 Unsnap the bezel & from the front of the handle of the line card. Access the retaining clips from the back of the line card handle, release the retaining clips #, and separate the PMD blank cover from the line card. 6 Disconnect the connectors of the receiver cable ' and the transceiver cable ( from the respective connectors on the bezel. 7 Remove the PMD daughter card $ from the line card. Break the connection by lifting up on the back of the PMD daughter card, and then unsnap the PMD daughter card from the two brass standoffs % mounted on the line card. 8 Install new PMD daughter card or blank PMD cover. To install a blank PMD cover snap the PMD cover into the selected port slot. To install a new PMD daughter card see the appropriate installation procedure for the PMD daughter card concerned. 9 Install the line card in the unit. See Installing the Logic Module. ------------------------------------------------------------ Replacing Modules 7-13 Installing the SMF PMD ------------------------------------------------------------ Installing the SMF PMD Unpacking the PMD ------------------------------------------------------------ Note ------------------------------------------------------------ (The extra posts are not used in this installation ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 1 Set up the ESD equipment. 2 Slip on ESD wrist band. 3 Unpack the PMD and check the contents against the packing slip. 4 Remove the cable-ties from the coiled cable bundle. ------------------------------------------------------------ Replacing Modules 7-15 Installing the SMF PMD Prepairing the SMF PMD Complete the following steps to prepare single-mode fiber (SMF) PMD (DEFXS-AA) daughter cards: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Identify the receiver cable !, the transceiver cable ", the bezel #, the coiled cable bundle $, the coiled cable tie point %, the lower port cable-tie anchor mounting location &, and the upper port cable-tie anchor mounting location '. ------------------------------------------------------------ MKV-0281-99ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ 4ðTX ------------------------------------------------------------ 6ðTX ------------------------------------------------------------ 7ðTX ------------------------------------------------------------ 5ðTX Installing the SMF PMD ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Note ------------------------------------------------------------ The receiver cable is the thin white cable. The transceiver cable is the thick yellow cable ------------------------------------------------------------ 4 Mate the connectors of the receiver cable ! and the transceiver cable " to the respective connectors on the bezel #. Orient the bezel # with the label area facing the top of the line card. Extend the loose ends of the receiver cable ! and the transceiver cable " through the hole in the line card. The receiver cable ! will be to the left and the transceiver cable " will be to the right. ------------------------------------------------------------ Caution ------------------------------------------------------------ Do not exceed the 3" minimum bend diameter when adjusting coils. ------------------------------------------------------------ 5 Roughly dress the coiled cable bundle $. Equalize the cables in the coiled cable bundle and dress the coiled cable bundle to the rear of the PMD daughter card as shown in the figure. ------------------------------------------------------------ Note ------------------------------------------------------------ Loosely install the cable-ties to allow for final dressing of the loops. ------------------------------------------------------------ 6 Install the cable-ties. Wrap one cable-tie around all the cables in the coiled cable bundle $ and attach it to the PMD daughter card using the after post hole on the TX side of the PMD daughter card. Wrap the other cable-tie around all the cables in the coiled cable bundle $ and position it near the RX connector. ------------------------------------------------------------ Replacing Modules 7-17 Installing the SMF PMD Mounting the SMF PMD Complete the following steps to mount the single-mode fiber (SMF) PMD (DEFXS-AA) daughter cards: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Identify the receiver cable !, the transceiver cable ", the bezel #, the coiled cable bundle $, the coiled cable tie point %, the lower port cable-tie anchor mounting location &, and the upper port cable-tie anchor mounting location '. ------------------------------------------------------------ MKV-0281-99ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ 4ðTX ------------------------------------------------------------ 6ðTX ------------------------------------------------------------ 7ðTX ------------------------------------------------------------ 5ðTX Installing the SMF PMD 3 Mate the connector by pressing down on the back of the PMD daughter card. 4 Snap the bezel # onto the front of the handle of the line card. Orient the bezel # with the label area facing the top of the line card. 5 Dress the cables in the coiled cable bundle and tighten the cable-ties. 6 Install final cable_tie. If SMF PMD daughter card is already installed in the port, attach the two coiled cable bundles together at the tie point % shown using a cable- tie. If this is the first SMF PMD daughter card to be installed, mount the cable-tie anchor in the appropriate position (the position for the upper port ' or the position for the lower port &), and attach the coiled cable bundle $ to the appropriate cable-tie anchor. 7 This step is for DAS configuration only. Repeat steps 4 through 6 to install the other PMD daughter card. 8 Place line card in a static proof bag. 9 Place bagged module on a flat surface or on another bagged module. The modules can be stacked four modules high. ------------------------------------------------------------ What is Next Proceed to Chapter 5 to test the system. Replacing Modules 7-19 Replacing a Blank Handle ------------------------------------------------------------ Replacing a Blank Handle Removing a Blank Handle Complete the following steps to remove a blank handle from the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the screws ! that fasten the selected blank handle " to the GIGAswitch System, the # guide pins, and the EMI shield $. ------------------------------------------------------------ mk28106ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX 1ðTX ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL06A.EPS3ðTX ------------------------------------------------------------ 4ðTX Replacing a Blank Handle Installing a Blank Handle Complete the following steps to install a blank handle: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the screws ! that fasten the selected blank handle " to the GIGAswitch System, the guide pins #, and the EMI shield $. ------------------------------------------------------------ mk28106ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX 1ðTX ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL06A.EPS3ðTX ------------------------------------------------------------ 4ðTX Replacing a Fan Tray Assembly ------------------------------------------------------------ Replacing a Fan Tray Assembly Removing the Fan Tray Assemblies ------------------------------------------------------------ Warning ------------------------------------------------------------ Remove all system modules from the unit to make it light enough for two people to lift the unit. ------------------------------------------------------------ Complete the following steps to remove the fan tray assemblies from the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the two fasteners ! that attach the selected fan tray assembly " to the GIGAswitch System, and the handle #. ------------------------------------------------------------ mk28152ðTX 1ðTX 3ðTX 2ðTX ------------------------------------------------------------ ------------------------------------------------------------ Replacing a Fan Tray Assembly Installing the Fan Tray Assemblies Complete the following steps to install the fan tray assemblies in the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the two fasteners ! that attach the selected fan tray assembly " to the GIGAswitch System, and the handle # of the selected fan tray assembly. ------------------------------------------------------------ mk28152ðTX 1ðTX 3ðTX 2ðTX ------------------------------------------------------------ ------------------------------------------------------------ Replacing a FEU ------------------------------------------------------------ Replacing a FEU Removing the FEU Complete these steps to remove a front end unit (FEU). ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the power switch !, the power cord ", the four screws # that fasten the selected module to the GIGAswitch System, and the handle $ of the selected module. ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL75A.EPS ------------------------------------------------------------ 1ðTX 2ðTX 3ðTX 4ðTX ------------------------------------------------------------ Replacing a FEU Installing the FEU Complete the following steps to install the front end units (FEUs): ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the power switch !, the power cord ", the four screws # that fasten the selected module to the GIGAswitch System, and the handle $ of the selected module. ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL75A.EPS ------------------------------------------------------------ 1ðTX 2ðTX 3ðTX 4ðTX ------------------------------------------------------------ Replacing a Power Supply Filler Panel ------------------------------------------------------------ Replacing a Power Supply Filler Panel Removing a Power Supply Filler Panel Complete the following steps to remove a power supply filler panel: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the screws ! that fasten the power supply filler panel" to the GIGAswitch System. ------------------------------------------------------------ mk28153 ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ Replacing a Power Supply Filler Panel Installing a Power Supply Filler Panel Complete the following steps to install a power supply filler panel: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the screws ! that fasten the power supply filler panel " to the GIGAswitch System. ------------------------------------------------------------ mk28153 ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ Replacing a PSA ------------------------------------------------------------ Replacing a PSA Removing the PSA Complete the following steps to remove the power status assembly (PSA). ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the four screws ! that fasten the module to the GIGAswitch System, the handle " of the module, and the slot # designated for the module. ------------------------------------------------------------ ------------------------------------------------------------ mk28169ðTX 3ðTX 2ðTX ------------------------------------------------------------ ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ Replacing a PSA Installing the PSA Complete the following steps to install the power status assembly (PSA). ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the four screws ! that fasten the module to the GIGAswitch System, the handle " of the module, and the slot # designated for the module. ------------------------------------------------------------ ------------------------------------------------------------ mk28169ðTX 3ðTX 2ðTX ------------------------------------------------------------ ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ Replacing a PSC Card ------------------------------------------------------------ Replacing a PSC Card Complete the following procedures to replace a power system controller (PSC) card: 1. Remove the PSA 2. Remove the PSC card 3. Install the PSC card 4. Install the PSA 7-30 Replacing Modules Replacing a PSC Card Removing the PSA Complete the following steps to remove the power status assembly (PSA). ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the four screws ! that fasten the module to the GIGAswitch System, the handle " of the module, and the slot # designated for the module. ------------------------------------------------------------ ------------------------------------------------------------ mk28169ðTX 3ðTX 2ðTX ------------------------------------------------------------ ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ Replacing a PSC Card Removing the PSC Card Once the power status assembly (PSA) has been removed, complete the following steps to remove the power system controller (PSC): ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the PSC card !, the PSA ", and the two cables # connecting the PSC card ! to the PSA ", and the standoffs $. ------------------------------------------------------------ mk28155ðTX ------------------------------------------------------------ 2ðTX 1ðTX J:\SOURCE\ART\NEWART\FINAL55A.EPS ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ 4ðTX Replacing a PSC Card Installing a PSC Card Complete the following steps to install a power system controller (PSC): ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the PSC card !, the PSA ", and the two cables # connecting the PSC card ! to the PSA ", and the standoffs $. ------------------------------------------------------------ mk28155ðTX ------------------------------------------------------------ 2ðTX 1ðTX J:\SOURCE\ART\NEWART\FINAL55A.EPS ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ 4ðTX Replacing a PSC Card Installing the PSA Complete the following steps to install the power status assembly (PSA). ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the four screws ! that fasten the module to the GIGAswitch System, the handle " of the module, and the slot # designated for the module. ------------------------------------------------------------ ------------------------------------------------------------ mk28169ðTX 3ðTX 2ðTX ------------------------------------------------------------ ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ 8 ------------------------------------------------------------ Removing the System from the Rack Chapter Contents ------------------------------------------------------------ Warning ------------------------------------------------------------ Remove all system modules from the unit to make it light enough for two people to lift the unit. See Chapter 7 for removal procedures ------------------------------------------------------------ This chapter describes the following procedures that should be completed to remove the GIGAswitch System in the rack. 1. Removing the upper plenum 2. Detaching the empty GIGAswitch System from the rack Time Required 45 minutes. Needed Tools You will need the following tools: · Number 2 cross-point screwdriver · ESD equipment · Static proof containers for modules Removing the System from the Rack 8-1 Removing the Upper Plenum ------------------------------------------------------------ Removing the Upper Plenum Complete the following steps to remove the upper plenum: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the upper plenum !, the four shoulder screws ", and the mounting screw #. ------------------------------------------------------------ ------------------------------------------------------------ 2ðTx Removing the Upper Plenum ------------------------------------------------------------ Detaching the Empty GIGAswitch System from the Rack Complete the following steps to detach the GIGAswitch System from the rack: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the GIGAswitch System !, and the twelve screws ". ------------------------------------------------------------ mk28162 ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 2ðTX Lowering the Empty GIGAswitch System ------------------------------------------------------------ Lowering the Empty GIGAswitch System ------------------------------------------------------------ Warning ------------------------------------------------------------ The Empty GIGAswitch System weighs 31.75 kg. Use two people to lift the unit. ------------------------------------------------------------ Complete the following procedure to lower the GIGAswitch System: ------------------------------------------------------------ 1ðTx ------------------------------------------------------------ 9 ------------------------------------------------------------ Replacing Backplanes Chapter Contents ------------------------------------------------------------ Caution ------------------------------------------------------------ Read Chapter 6 before attempting to replace a logic or power backplane, as described in this chapter. ------------------------------------------------------------ ------------------------------------------------------------ Note ------------------------------------------------------------ The modules from the selected backplane should have already been removed (see Chapter 7) for to remove the modules ------------------------------------------------------------ This chapter describes the procedures for replacing the logic and power backplanes. Time Required 60 minutes. Tools Required · Number 2 cross-point screwdriver · Thin flat blade (4.41 mm (3/16 in)) screwdriver Procedures · Accessing the backplanes · Replacing the logic backplane · Replacing the power backplane · Restoring the system Replacing Backplanes 9-1 Accessing the Backplanes ------------------------------------------------------------ Accessing the Backplanes This section contains the following procedures: · Removing the back door · Installing the back door Replacing Backplanes 9-3 Accessing the Backplanes Removing the Back Door Complete the following steps to remove the back door from the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the 10 screws ! that fasten the back door to the GIGAswitch System# and the lower lip " used to remove the back door. ------------------------------------------------------------ 3ðTx 2ðTx 1ðTx mkv-0281-59 ðTx ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Accessing the Backplanes Installing the Back Door Complete the following steps to install the back door on the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the screws ! that fasten the back door to the GIGAswitch System#, and the back door ". ------------------------------------------------------------ 3ðTx 2ðTx 1ðTx mkv-0281-59 ðTx ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Replacing the Power Backplane ------------------------------------------------------------ Replacing the Power Backplane Removing the Back Door Remove the back door (see Accessing the Backplanes ) Removing the Power Backplane Complete the following steps to remove the power backplane from the GIGAswitch System. ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the four screws ! that fasten the power backplane " to the GIGAswitch System, and the three cables # used to connect the power backplane " with the logic backplane $ and with the fan tray assemblies. ------------------------------------------------------------ ------------------------------------------------------------ 2ðTx ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 1ðTx ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Replacing the Power Backplane ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 3 ðTX ------------------------------------------------------------ ------------------------------------------------------------ 4ðTX mk28161ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Replacing the Power Backplane Installing the Power Backplane Complete the following steps to install the power backplane onto the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the four screws ! that fasten the power backplane " to the GIGAswitch System, and the three cables # used to connect the power backplane " with the logic backplane and with the fan tray assemblies. ------------------------------------------------------------ ------------------------------------------------------------ 2ðTx ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 1ðTx ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Replacing the Power Backplane ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 3 ðTX ------------------------------------------------------------ ------------------------------------------------------------ 4ðTX mk28161ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Replacing the Logic Backplane ------------------------------------------------------------ Replacing the Logic Backplane Removing the Back Door Remove the back door (see Accessing the Backplanes ) Removing the Logic Backplane Complete the following steps to remove the logic backplane from the GIGAswitch System: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the six screws ! that fasten the logic backplane " to the GIGAswitch System, and the cable # used to interconnect the logic backplane with the power backplane. ------------------------------------------------------------ 3D20281:Source:Art:figure-28:P-140.eps ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 2ðTx 3ðTx ------------------------------------------------------------ 1ðTx ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Replacing the Logic Backplane ------------------------------------------------------------ ------------------------------------------------------------ 2 Disconnect, unplug, and remove the cable assembly #. Loosen the two screws on each connector (backplane and chassis sides) using a thin flat blade (4.41 mm (3/16 in)) screwdriver. 3 Remove the six screws ! using a number 2 cross-point screwdriver. Remove the three lower screws first, then remove the three upper screws. 4 Lift the logic backplane away from the GIGAswitch System. Rotate the backplane slightly (right side turning inward and the left side turning outward during removal). ------------------------------------------------------------ Replacing Backplanes 9-11 Replacing the Logic Backplane Installing the Logic Backplane ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Locate the screws ! that fasten the logic backplane " to the GIGAswitch System, and the cables # used to connect the logic backplane " with the fan tray assemblies. ------------------------------------------------------------ 3D20281:Source:Art:figure-28:P-140.eps ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 2ðTx 3ðTx ------------------------------------------------------------ 1ðTx ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Replacing the Logic Backplane ------------------------------------------------------------ ------------------------------------------------------------ 2 Insert the lower edge of the backplane behind the power connector and into the lower right corner of unit. 3 Install the six screws (three upper and three lower) ! (1) using a number 2 cross-point screwdriver. Install the three upper screws first, then install the three lower screws. 4 Install the cable assembly #. Plug in the connector and tighten the two screws using a thin flat blade (4.41 mm (3/16 in)) screwdriver. ------------------------------------------------------------ Installing the Back Door Remove the back door (see Accessing the Backplanes ) Replacing Backplanes 9-13 Restoring the System ------------------------------------------------------------ Restoring the System Complete the following procedures to restore the system: · Install the modules in the selected backplane (See Chapter 7). Replacing Backplanes 9-15 Part IV ------------------------------------------------------------ Reference Part IV contains reference information. · Appendix A provides the physical, electrical, and environmental specifications for the GIGAswitch System. · Appendix B describes the cooling and power modules in the fan tray assembly, FEU, PSA, and the PSC card families. · Appendix C describes the logic modules in the line card, physical medium dependent (PMD) daughter card, SCP card, CBS card, and clock card families. · Appendix D provides guidelines for installing additional logic modules. A ------------------------------------------------------------ GIGAswitch System Specifications This appendix provides the specifications for the GIGAswitch System. These specifications include: · Physical specifications for the GIGAswitch System. · Electrical specifications for the GIGAswitch System. · Environmental specifications for the GIGAswitch System. GIGAswitch System Specifications A-1 Physical Dimensions of the GIGAswitch System ------------------------------------------------------------ Physical Dimensions of the GIGAswitch System The following table shows the physical specifications for the GIGAswitch System. Allow 90.0 cm (35.4 in) contiguous vertical space for the installation of the GIGAswitch System, the lower plenum, and the upper plenum. (Physical Specifications) ------------------------------------------------------------ Parameter Min Typ Max Units Symbol ------------------------------------------------------------ Mounting type Rack Mounted - - Height - 896.2 - millimeters mm - 35.25 - inches in Width - 507 - millimeters mm - 19.95 - inches in Depth - 495 - millimeters mm - 19.50 - inches in Weight - 87.1 - kilogams kg - 192 - pounds lb Operation clearance (front) 51 - - millimeters mm 2.0 - - inches in Operation clearance (rear) 76 - - millimeters mm 3.0 - - inches in Operation clearance (side) 0 - - millimeters mm 0 - - inches in Service clearance (front) 914 - - millimeters mm 36.0 - - inches in Service clearance (rear) 914 - - millimeters mm 36.0 - - inches in Service clearance (side) 0 - - millimeters mm 0 - - inches in Service clearance (top) 0 - - millimeters mm 0 - - inches in Shipping height§ - 1283 - millimeters mm - 50.5 - inches in Shipping width§ - - millimeters mm - 26.0 - inches in Shipping depth§ - - millimeters mm - 32.0 - inches in Shipping weight§ - 99.8 120 kilograms kg - 220 264 pounds lbs ------------------------------------------------------------ §Shipping for standard shipping container ------------------------------------------------------------ GIGAswitch System Specifications A-3 Electrical Information ------------------------------------------------------------ Electrical Information AC Input Power Requirements The following table shows the ac input power requirements for the GIGAswitch System. ------------------------------------------------------------ Parameter Min Typ Max Units Symbol ------------------------------------------------------------ Nominal Voltage - 120 - volts V Operational Voltage Range 93 - 264 volts V Nominal Frequency - 50/60 - hertz Hz Frequency Range 47 - 63 hertz Hz Number of Phases - 1 - none NA 120V Single Phase Input Current (Steady State) - 8.0 15 amperes A 120V Single Phase Input Current (Neutral N) - 4.0 7.5 amperes A 120V Single Phase Input Current (Ground G) - 1.0 - milliamperes mA 240V Single Phase Input Current (Steady State) - 4.0 7.5 amperes A 240V Single Phase Input Current (Neutral N) - 4.0 7.5 amperes A 240V Single Phase Input Current (Ground G) - 1.0 - milliamperes mA Ride-Through Time 100 - - milliseconds ms Inrush Current - - n/a amperes peak A Start-Up Current - - n/a rms amperes A Start-Up Current Duration - - n/a seconds s Power Consumption - 800 1250 watts W Apparent Power - 1052 1316 volt amperes VA Power Factor - .95 - none PF Crest Factor - 1.37 - none CF ------------------------------------------------------------ Power Cord Types The following table lists the power cords used in the various country kits available with the GIGAswitch System. ------------------------------------------------------------ Country Part Number Country Part Number ------------------------------------------------------------ Denmark BN16A-2E Israel BN18W-2E UK/Ireland BN12A-2E Central Europe BN13A-2E Italy BN17A-2E Austraila BN22C-2E Switzerland BN14A-2E New Zealand BN22C-2E ------------------------------------------------------------ Line cords are 2.5 meters in length. Use different outlets and services breakers for redundant power supplies.) A-4 GIGAswitch System Specifications Electrical Information DC Power Requirements The following table shows the DC power requirements for the GIGAswitch System. ------------------------------------------------------------ Parameter Min Typ Max Units Symbol ------------------------------------------------------------ Power Consumption - 640 1000 watts W Current at 48 Vdc - 12 20 amperes A Current at 12-26 Vdc -- 3.6 5.0 amperes A DC voltage range (48 Vdc) 46.32 - 49.68 volts Vdc DC voltage range (12Vdc - 26 Vdc) 11.0 - 27.1 volts Vdc Output Watts Available - - 1000 watts W Current available at 48 Vdc - - 22. amperes A Current available at 11-27.1 Vdc -- - 1.5-5.0 amperes A ------------------------------------------------------------ GIGAswitch System Specifications A-5 Environmental Information ------------------------------------------------------------ Environmental Information ------------------------------------------------------------ Parameter Min Typ Max Units Symbol ------------------------------------------------------------ Temperature (Operating) 10 - 35 degrees Celsius °C 50 - 95 degrees Fahrenheit °F Altitude derating - 1.8 - degrees Celsius per kilometer °C/km - 1.0 - degrees Fahrenheit per 1000 feet °F/1000 ft Temperature (Nonoperating) -40 - 66 degrees Celsius °C -40 - 151 degrees Fahrenheit °F Temperature (Storage) -40 - 66 degrees Celsius °C -40 - 151 degrees Fahrenheit °F Relative Humidity (Operating) 10 - 90 percent relative humidity (noncondensing) %RH Relative Humidity (Nonoperating) <50 - 95 percent relative humidity (noncondensing) %RH Relative Humidity (Storage) <50 - 95 percent relative humidity (noncondensing) %RH Maximum Wet Bulb Temperature (Operating) - - 25 degrees Celsius °C - - 77 degrees Fahrenheit °F Maximum Wet Bulb Temperature (Storage) - - 146 degrees Celsius °C - - 115 degrees Fahrenheit °F Minimum Dew Point Temperature (Operating) 2 - - degrees Celsius °C 36 - - degrees Fahrenheit °F Heat Dissipation - 800 1250 watts W - 2730 4265 Btu/hr Btu/hr Altitude (Operating) - - 2400 meters above sea level m - - 8000 feet above sea level ft Altitude (Nonoperating) - - 4900 meters above sea level m - - 16000 feet above sea level ft Mechanical Shock (Operating) Duration 10+3 milliseconds ms Level 10g gravities G Vibration Freq Range (Operating) 5 - 500 hertz Hz Vibration Level (Operating) .010- in DB .25g peak Mechanical Shock (Nonoperating) Duration 29.2 milliseconds ms Level 13.67 gravities G Vibration Freq Range (Nonoperating) 10 - 300 hertz Hz Vibration Level (Nonoperating) 1.40g - .029 gz/hz Acoustic Emission (Operating) - - Bels B A-6 GIGAswitch System Specifications Environmental Information ------------------------------------------------------------ Parameter Min Typ Max Units Symbol ------------------------------------------------------------ Acoustic Emission (LNPE) - 5.9 - decibels dBA Acoustic Emission (LPA) - 46 - decibels dBA Acoustic Emission (Idle /Standby) - - Bels B Acoustic Emission (LNPE) - 5.9 - decibels dBA Acoustic Emission (LPA) - 46 - decibels dBA Airflow Intake Location Top-Front Airflow Exhaust Location Bottom Rear ------------------------------------------------------------ Ventilation The GIGAswitch System cooling system is designed to be tolerant of various rack installation configurations. However, to provide adequate ventilation: · Do not block off the inlet air vents (upper grilles). · Do not block off the outlet air vents (lower grilles). · Do not allow the cooling air entering the GIGAswitch System to rise above 32°C (90°F). EMI Susceptibility The following table shows the electromagnetic interference (EMI) susceptibility for the GIGAswitch System. ------------------------------------------------------------ Parameter Maximum Units Symbol ------------------------------------------------------------ Broadband Conducted EMI Class A Composite (FCC/VDE) -3db Volts dbuv dbuv Narrowband Conducted Transients Frequency Range 10KHZ to 30MHZ kilohertz, megahertz kHz, MHz V rms into 50 ohms 3VRMS Volts V Narrowband Radiated Susceptibility Frequency Range .01MHZ- 1GHZ kilohertz, megahertz kHz, MHz Level 5 Volts/M Volts per Meter V/m ESD Control 15KV kilovolts kV ------------------------------------------------------------ GIGAswitch System Specifications A-7 B ------------------------------------------------------------ Cooling and Power Modules This appendix provides a description of the cooling and power modules belonging to the following families: · Fan tray assembly · Front end unit (FEU) · Power status assembly (PSA) · PSC card Cooling and Power Modules B-1 Fan Tray Assembly ------------------------------------------------------------ Fan Tray Assembly The fan tray assembly (70-30578-01) is a member of the fan tray assembly family of cooling modules. The fan tray assembly contains two 5.75 inch fans used to provide convective cooling to the GIGAswitch System. These variable speed fans are controlled by the PSC card based on ambient temperature. Air Flow The air above the GIGAswitch System is drawn from the front of the GIGAswitch System, directed on the modules inside the GIGAswitch System, and exhausted from the bottom rear of the GIGAswitch System. LED Meaning The following figure identifies the LEDs on the fan tray assembly. mk28111ðTX J:\SOURCE\ART\NEWART\FINAL11B.EPS ------------------------------------------------------------ 1ðTX FEU ------------------------------------------------------------ FEU The front end unit (FEU) (DEFGB-AB) is a member of the FEU family of power modules. Function Front end unit (FEU) converts primary AC power to system 48 Vdc and to 12 Vdc through 26 Vdc fan power. The FEU also houses the system circuit breaker. LEDs The following figure identifies the LEDs on the FEU. mk28112ðTX C:\PROJECTS\SUNOMA\FINALS\FINAL12B.EPS ------------------------------------------------------------ 2ðTX 1ðTX ------------------------------------------------------------ 3ðTX PSA ------------------------------------------------------------ PSA Description The power status assembly (PSA) (70-30585-01) is a member of the FEU family of power modules. Function The PSA houses the security switch and the PSC card. Security Switch The security switch controls the ability to configure or monitor the GIGAswitch System using in-band § or out-of-band (OBM) + management commands. The following table identifies the various positions of the security switch. ------------------------------------------------------------ Position Name Function Access Allowed? § Out-of-Band In-Band ------------------------------------------------------------ 1 1 No Access No No 2 2 Secure Access With password SNMP Get, and getnext PDUs only 3 3 Normal Access With password SNMP Get, getnext, and set PDU 4 4 Easy Access Without password SNMP Get, getnext, and set PDUs ------------------------------------------------------------ §Security for out-of-band management is set by password. Security for in-band management is set by community and privileged port designation. Both can be changed using in-band or out-of-band management commands. ------------------------------------------------------------ PSC The PSC card is an FRU that is mounted on the PSA. LED Testing All LEDs are lit for one second during start-up to ensure that the LEDs are operational. After start-up only those LEDs indicating faults remain lit. ------------------------------------------------------------ § Issued from any GIGAswitch System management station. + Issued through the terminal/modem interface for the GIGAswitch System. B-4 Cooling and Power Modules PSA LED Meaning The following figure and associated table identify the security switch and the LEDs on the PSA. mk28109ðTX J:\SOURCE\ART\NEWART\FINAL09B.EPS ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ 1ðTX PSC Card ------------------------------------------------------------ PSC Card The power system controller (PSC) card (54-22132-01) is a member of the FEU family of power modules. The PSC card is a module that snaps onto standoffs on the PSA. The PSC card automatically plugs into the power backplane when the PSA is installed in the GIGAswitch System. Function The PSC card is that portion of the GIGAswitch System that controls and monitors the redundant 48 Vdc power supplies, and the fan tray assemblies. The PSC card reports the operational status of the monitored units to the clock card. The PSC card performs the following functions: · MST diagnostics, and fan tests at start-up. · Temperature and fan speed monitoring. · Fan speed control to minimize audible noise and to insure sufficient cooling. · Power and cooling system status, configuration and fault reporting by way of the serial bus to the clock card. · Power failure early warning signaling to the clock card. · Power and cooling system LED LEDs on/off control. · System security key switch monitoring. Description The following figure shows the physical characteristics of the PSC card. C ------------------------------------------------------------ Logic Modules This appendix describes of the logic modules belonging to the following families: · Line card · PMD daughter card · SCP card · Clock card · CBS card Logic Modules C-1 Line Card ------------------------------------------------------------ Line Card The 2-port FDDI line card (DEFGL-AA) is a member of the line card family of logic modules. Hotswap Capability The line card can not be replaced without removing the power from the system. Function The line card performs bridge forwarding functions, including packet filtering, assisting in learning, and determining the correct output data link to which a packet should be forwarded. Packets with unknown destinations, multicast packets, or exceptions are sent to the switch control processor (SCP). The line card implements two fully independent FDDI forwarding bridge ports and interfaces these ports to the CBS card. Either or both ports may be configured in a single-attachment station (SAS) or a dual-attachment station (DAS) mode. Each of the two line card ports is capable of processing over 430,000 FDDI packets per second while the maximum connection rate from the line card to the CBS card is over 500,000 connections per second. mk28176ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX Line Card LEDs on Line Card The following figure identifies the LEDs and connectors on the line card and the associated PMD daughter cards. mk28108ðTX ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL08A.EPS ------------------------------------------------------------ 4ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ ------------------------------------------------------------ Line Card LED Meaning The following table provides the meaning for the line card LEDs . ------------------------------------------------------------ Indication Number/Name OFF Amber Green Green/Amber ------------------------------------------------------------ !/PMD FRU LED PMD OK and fully operational or no power. Steady - PMD loop test failed (defective PMD FRU) Flashing - Reserved Steady - Reserved Flashing - Reserved Flashing - Reserved "/PMD PHY LED No power or severe fault Steady - Link confidence test (LCT) failure Flashing - Topology reject Steady - Connection accepted Flashing - Awaiting a connection Flashing - Standby (dual-homing) #/Line card LED No power or with port LEDs off and PMD daughter card LEDs on, card is not fully seated or in process of being removed. Steady - MST failed or fatal firmware error. Flashing - MST in progress (wait) Steady - MST passed Flashing - Firmware down-line load (DLL) in progress - will flash at 1/2 second intervals. Flashing - Non- fatal firmware error. $/Port LED No power or or with port LEDs off and PMD daughter card LEDs on, card is not fully seated or in process of being removed. Steady - MST failure in this port, Flashing - MST in progress (Wait) Steady - MST passed, port active and in forwarding state. Flashing - MST passed, port in backup, preforwarding state or station management is off. Flashing - Reserved ------------------------------------------------------------ C-4 Logic Modules PMD Daughter Cards ------------------------------------------------------------ PMD Daughter Cards The line card can have up to four physical medium dependent (PMD) daughter cards installed as independent field replaceable units (FRUs). The PMD daughter card houses a PMD option § Each PMD daughter card contains a PMD FRU LED and a PMD PHY LED. The following figure and table identify the various PMD options. ------------------------------------------------------------ Name Part Number Description PMD Loopback ------------------------------------------------------------ ! Single-Mode Fiber 12-34685-01 12-34830-01 FC-to-FC " ANSI Multimode Fiber BN24B-xx § 12-32005-01 FDDI-to-FDDI " ANSI Multimode Fiber BN24D-xx § 12-32005-01 FDDI-to- 2.5 mm ST-type # Blank PMD Bezel ------------------------------------------------------------ §xx = cable length in meter (See Fiber Distributed Data Interface Media Connection Information). ------------------------------------------------------------ G:\SOURCE\ART\NEWART\FINAL71D.EPSG:\SOURCE\ART\NEWART\FINAL71E.EPS SCP Card ------------------------------------------------------------ SCP Card The switch control processor (SCP) card (DEFGP-AA) is a member of the SCP card family of logic modules. Application The most common application for the SCP card is to serve as the System Control Processor (SCP) for the GIGAswitch System. During system initialization, an election takes place in software to assign one SCP card the role of primary SCP. If other switch engines are installed, they might be used by the system as backup SCPs for redundancy. SCP Function The SCP function includes central functions such as initialization, remote management, and control of services (such as bridging) that are distributed across modules. One of the major bridging services is to send and receive packets that cannot be handled by the line cards. The SCP card sends and receives packets for these purposes, among others: · Exchanging intraswitch control packets between SCPs and line cards, including background monitor (keep-alive packets, address learning packets for transparent bridging, and packets to read or set management parameters. · Forwarding multicast packets to an SCP by each line card. The primary SCP uses special resources in the system to broadcast each packet to the proper set of outbound line-card ports and other switch engines. · Interpreting network control packets diverted from line cards. · Acting as a station on the network and emitting packets for remote management the GIGAswitch System. C-6 Logic Modules SCP Card SCP Card LEDs and Control mk28110ðTX J:\SOURCE\ART\NEWART\FINAL10A.EPS ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 2ðTX 1ðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ ------------------------------------------------------------ SCP Card SCP HEX LED Table The following table further identifies the purpose of the SCP LEDs. ------------------------------------------------------------ Number/Event LED ! Condition HEX LED " Condition Meaning ------------------------------------------------------------ 1/SCP card startup Amber Out MST has not passed. 2/Startup complete Solid amber LED F Startup complete 3/SCP card MST Flashing amber test number updated MST in progress Solid green B MST passed, SCP card in backup mode Solid amber or out solid number MST failed 4/SCP election Solid green E Elected switch control processor 5/Downline load Solid green D New firmware images are being loaded into the flash memory during a firmware upgrade. Solid green Alternating D/E Corrupt image detected during system boot. SCP continues to try to retrieve a good image from the bootserver. Solid green Test passed Solid amber Test failed ------------------------------------------------------------ C-8 Logic Modules Clock Card ------------------------------------------------------------ Clock Card The clock card (54-22120-01) is a member of the clock card family of logic modules. The clock card must be included in any GIGAswitch System configuration. Application The clock card performs the following functions: · Clock generation and distribution · Arbitration · Terminal or modem interface · PSC card interface · PSC card power source Clock Generation and Distribution The clock card generates master system clocks and distributes them through the backplane to each of the line card and the SCP card. This allows resources associated with the backplane (in particular the CBS card and the Backplane bus) to be used in a synchronous and efficient manner. Arbitration The clock card also arbitrates access to the backplane bus to grant ownership of the potential users in a fair manner. Terminal or Modem Interface The clock card provides the GIGAswitch System user with a standard terminal or modem interface conforming to RS232 specifications, and compatible with RS423. The interface can be used to connect a terminal to GIGAswitch System for local management and diagnostic purposes. Full modem support is also provided for remote maintenance and diagnostic support. User specific parameters, such as baud rates, stop bits, parity, data length and so forth are stored locally on the clock card in nonvolatile (FLASH) memory. PSC Card Interface The clock card receives environmental status from the PSC card when requested. This status includes: · Power supply status · The state of the fans · Ambient temperature Line Card Monitoring and Power Control The clock card monitors line card, SCP card, and CBS card to determine the type of card present during power initialization, and to determine when a card is removed or inserted. The major functions of the clock card are: · Clock generation and distribution. · Backplane bus arbitration and power sourcing. Logic Modules C-9 Clock Card · Arbitration and tie breaking on behalf of the SCP card. · Local console (terminal or modem interface. · Sensing and control of the environment and of other modules. In addition, many centralized resources exist on the clock card. Examples of such resources include the many Ethernet addresses associated with each GIGAswitch System platform, network and local management parameters, and parameters learned about any local topology. C-10 Logic Modules Clock Card Clock Card LEDs J:\SOURCE\ART\NEWART\FINAL32B.EPS ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ CBS Card ------------------------------------------------------------ CBS Card The crossbar switch (CBS) card (54-22116-01) is a member of the CBS card family of logic modules. The crossbar is comprised of three CBS-36 chips each operating in 36x36x2 mode to make a 6-bit wide, 36 port crossbar. Function The function of the CBS card is to connect numerous 100 Mbit links together in a dynamic fashion. Any input port may be connected to any single-output or group of outputs. Each connection must be specified individually. Specifications The CBS card has an aggregate maximum bandwidth of 3.6 Gigabits/second. Connections are made through the crossbar between 100 Mbit/second links at a maximum rate of 6.25 million connections per second. Half duplex connections are made independently; a full duplex connection may be established as two half duplex connections. C-12 Logic Modules CBS Card CBS LEDs mk28133ðTX ------------------------------------------------------------ J:\SOURCE\ART\NEWART\FINAL33A.EPS ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ D ------------------------------------------------------------ Guidelines for Installing Additional Modules This appendix provides guidance for installing additional logic module. Guidelines for Installing Additional Modules D-1 Identifying the Contents of the GIGAswitch System ------------------------------------------------------------ Identifying the Contents of the GIGAswitch System The contents of the GIGAswitch System depend on any options the customer may have ordered. These options were installed in the GIGAswitch System before shipment. Refer to the following figure and table to identify the contents of the GIGAswitch System configuration. mk28107FðTX ðTX ------------------------------------------------------------ 2ðTX ------------------------------------------------------------ 1ðTX ------------------------------------------------------------ 3ðTX ------------------------------------------------------------ 4ðTX ------------------------------------------------------------ 6ðTX ------------------------------------------------------------ 8ðTX ------------------------------------------------------------ 7ðTX ------------------------------------------------------------ 9ðTX ------------------------------------------------------------ 5ðTX Identifying the Contents of the GIGAswitch System ------------------------------------------------------------ Number Order Number Description ------------------------------------------------------------ ! DEFGL-AA A line card with the requested PMD daughter cards (ordered separately) installed §. One line card is included with the DEFGA-BA, and DEFGA-BB versions of the product. Additional line cards can be ordered separately by the customer. " DEFGP-AA A SCP card. One SCP card is included in all versions of the product. Additional SCP cards can be ordered separately by the customer. # 54-22120-01 A clock card is included in all versions of the product. $ 54-22116-01 A CBS card is included in all versions of the product. % 70-30587-05 All empty logic slots are covered by blank handles. & 70-30578-01 Two fan tray assemblies are included in all versions of the product. ' DEFGB-AB A FEU is included in all versions of the product. One additional FEU can be ordered as a redundant power supply. ( 70-30585-01 A PSA is included in all versions of the product. ) 74-45749-01 A power supply filler panel is included in all versions of the product. It covers the empty slot that can be occupied by the optional redundant FEU. ------------------------------------------------------------ §See the Fiber Distributed Data Interface Media Connection Information document for available versions, part numbers, and associated loopback connectors. ------------------------------------------------------------ Guidelines for Installing Additional Modules D-3 Recommended Location for Logic Modules ------------------------------------------------------------ Recommended Location for Logic Modules Although line cards or SCP cards can fit in any slot (except 7 or 8) 1 Digit al recommends the positions identified in the following figure for these reasons: · High availability: Zone 1 and zone 2 2 are cooled by different fans so the first SCP card is placed in slot 4 (zone 1) and the second SCP card is placed in slot 13 (zone 2). · Minimum future upgrade impact: 2-port backplane slots 3 are filled first. This leaves the 4-port backplane slots 4 open for 4-port line cards when they become available. The following figure identifies where each additional line card and SCP card should be installed §. ------------------------------------------------------------ 1 Slot 7 is reserved for the CLK card only. Slot 8 is reserved for the CBS card only. 2 Zone 1 = slots 1 through 7. Zone 2 = slots 8 through 14. 3 2-port slots = 1,2,3,4,13, and 14 4 4-port slots = 5,6,9,10,11, and 12 § All empty logic slots are covered by blank handle (70-30587-05)s. D-4 Guidelines for Installing Additional Modules Recommended Location for Logic Modules ------------------------------------------------------------ Abbrev. Order Number Description ------------------------------------------------------------ LC DEFGL-AA A line card with the requested PMD daughter cards (ordered separately) installed. One line card is included with the DEFGA-BA, and DEFGA-BB versions of the product. Additional line card can be ordered separately by the customer. SE DEFGP-AA A SCP card. One SCP card is included in all versions of the product. Additional SCP cards can be ordered separately by the customer. CLK 54-22120-01 A clock card is included in all versions of the product. CBS 54-22116-01 A CBS card is included in all versions of the product. ------------------------------------------------------------ Guidelines for Installing Additional Modules D-5 ------------------------------------------------------------ Index A ------------------------------------------------------------ Access See Security Accessory kit (70-30582-01), 2-6 contents of, 2-8 B ------------------------------------------------------------ Back door installing, 9-5 removal or installation of (fig), 9-4, 9-5 removing, 9-4 Backplane replacement, 9-1 Backplanes preparing to replace, 6-1 Backup Front end unit (FEU) (DEFGB-AB) function of, 1-6 location of (fig), 1-6 Blank handle installing, 7-21 replacement of (fig), 7-20, 7-21 Blank handle (70-30587-05) logic slots and, D-3 removing, 7-20 C ------------------------------------------------------------ CBS card function of, C-12 removal prerequisites, 6-2 specifications for, C-12 Clip nuts installation of (fig), 2-16 installing on rack, 2-16 positioning on rack, 2-14 Clock card function of, C-9 removal prerequisites, 6-2 Clock card (54-22120-01) configurations included in, D-3 description of, C-9 evaluating LEDs on (table), 5-18, 5-19, 5-21, C-11, C-13 function of, 1-8 location of (fig), 1-8 part number, C-9 Clock card (54-22120-01) (fig), 5-18, C-11 Commands Dispatcher mode (fig), 5-4 Terminal protocol mode (fig), 5-4 Configuration guidelines (fig), D-5 Connector, terminal See OBM port Connectors logic module (fig), 1-9 power module (fig), 1-7 Console port See OBM port Controls logic module (fig), 1-9 power module (fig), 1-7 Cooling and power modules installing, 3-11, 7-29, 7-34 Cooling and Power Modules, B-1 Cooling modules controls, LEDs, connectors (fig), 1-7 functions of, 1-6 location of (fig), 1-5 types of, 1-6 Cooling modules (fig), 1-6 Crossbar switch (CBS) card (54-22116-01) configurations included in, D-3 description of, C-12 evaluating LEDs on (table), 5-18, 5-19, 5-21, C-11, C-13 function of, 1-8 location of (fig), 1-8 part number, C-12 Crossbar switch (CBS) card (54-22116-01) (fig), 5-19, C-13 D ------------------------------------------------------------ DAS port identification of (fig), 1-4, C-2 Diagnostic boot (fig), 5-9 Diagnostic mode entering, 5-9 Diagnostic Mode Example of using (fig), 5-13 Index-1 Diagnostic modes Interconnection (fig), 5-3 Menus (fig), 5-2 E ------------------------------------------------------------ EMI shield damage to, 7-21 Example configuration description of, 1-4 F ------------------------------------------------------------ Fan tray assembly replacement of (fig), 2-36, 3-12, 7-22, 7-23 Fan tray assembly (70-30578-01) configurations included in, D-3 evaluating LEDs (table), 5-22, B-2 function of, 1-6 location of (fig), 1-6 status LED, B-2 Fan tray assembly (70-30578-01) (fig), B-2 Fan tray assembly (70-30578-01)s removing, 2-36, 7-22 Fault isolation PSA, B-4 Front end unit (FEU) installing, 3-10, 7-25 replacement of (fig), 2-38, 3-10, 7-24, 7-25 Front end unit (FEU) (DEFGB-AB) configurations included in, D-3 evaluating LEDs (table), 5-22, B-3 function of, 1-6 location of (fig), 1-6 removing, 2-38, 7-24 Front end unit (FEU) (DEFGB-AB) (fig), B-3 Function of PSA, B-4 security switch positions, 4-4, B-4 G ------------------------------------------------------------ GIGAswitch System applying power to, 2-10, 5-6 attaching to rack, 3-6 attaching to the rack (fig), 3-6, 8-3 configuration guidelines for, D-1 contents of, 2-6 contents of (fig), D-2 description of, 1-2 detaching from rack, 8-3 disconnecting from the pallet (fig), 2-5 electrical, A-4 environment, A-6 lifting of (fig), 3-5, 8-4 lowering of, 8-4 GIGAswitch System (cont'd) physical dimensions, A-3 rebooting, 5-7, 5-10 rebooting into diagnostic mode, 5-9 removing, 8-1 sections of, 1-5 Sections of (fig), 1-5 specifications, A-1 temperature status LED, B-5 ventilation, A-7 GIGAswitch System contents of, D-2 GIGAswitch System options for, D-2 H ------------------------------------------------------------ hotswap modules eligible for, 1-8 Hotswap modules eligible for, 1-6 I ------------------------------------------------------------ Input power connector, 1-6 Input power switch, 1-6 Installation tasks module removal, 2-21 K ------------------------------------------------------------ Key operated switch See Security switch L ------------------------------------------------------------ LED PSA, interpretation of, B-4 LEDs cooling module (fig), 1-7 logic module (fig), 1-9 power module (fig), 1-7 Line card removal prerequisites, 6-2 logic backplane replacement of (fig), 9-10 Logic backplane installing, 9-12 removal prerequisites, 6-2 Logic backplane (54-21849-01) removing, 9-10 logic module replacement of, 2-22, 7-4 replacement of (fig), 3-13 Logic module Clock card (54-22120-01), C-9 crossbar switch (CBS) card (54-22116-01), C-12 Index-2 Logic module, additional location for, D-1 Logic modules, C-1 controls, LEDs, connectors (fig), 1-9 functions of, 1-8 LEDs (fig), 5-20 location of (fig), 1-5 removing, 2-22, 7-3 slot restrictions, 1-8 types of, 1-8 Logic modules (fig), 1-8, 6-2 Lower plenum attaching to rack, 2-19 function of, 2-7 installation of (fig), 2-19 Lower plenum bracket attaching to rack, 2-18 installation of (fig), 2-18 M ------------------------------------------------------------ Maintenance jumper Location of (fig), 5-10 Module removal prerequisites for, 6-1 Module replacement, 7-1 Modules installing, 3-9 removing, 2-21 Modules, cooling and power controls, LEDs, connectors (fig), 1-7 Modules, cooling and power (fig), 1-6 Modules, logic controls, LEDs, connectors (fig), 1-9 Modules, logic (fig), 1-8, 6-2 O ------------------------------------------------------------ OBM port access control, 4-4, B-4 location of, 1-9 password requirements, 4-4, B-4 OBM terminal rebooting from, 5-7, 5-9, 5-10 OBM Terminal connection of (fig), 4-2 Out-of-band management connector See OBM port Out-of-band port terminal See OBM Terminal P ------------------------------------------------------------ Package contents accessory kit, 2-8 accessory kit (fig), 2-8 GIGAswitch System, D-2 identifying, 2-6 Package contents (cont'd) rack mount kit, 2-7 rack mount kit (fig), 2-7 unpacking, 2-4 Pallet removal of (fig), 3-4 Part number Clock card (54-22120-01), C-9 crossbar switch (CBS) card (54-22116-01), C-12 power status assembly (PSA) (70-30585-01) , B-4 PHY Key Replacement of (fig), 2-27 Plenum See Lower plenum and Upper plenum function of, 2-7 PMD installing the MMF ANSI MIC PMD (DEFXM-AA), 2-26, 7-9 installing the SMF PMD (DEFXS-AA), 2-31, 7-15 PMD daughter card evaluating LEDs on (table), 5-21 Installing a MMF ANSI MIC PMD (DEFXM-AA) (fig), 2-28, 7-6, 7-10 removing, 7-12 removing MMF ANSI MIC PMD (DEFXM-AA), 7-6 PMD daughter card (fig), C-5 PMD daughter card, SMF installation of (fig), 2-32, 2-34, 7-16, 7-18 Removal (fig), 7-12 2-port FDDI line card (DEFGL-AA) configurations included in, D-3 evaluating LEDs on (table), 5-15, 5-21 function of, 1-8 location of (fig), 1-8 2-port FDDI line card (DEFGL-AA) (fig), 5-15, C-3 2-port FDDI line card (DEFGL-AA)s removing, 7-2 Port type verifying (fig), 1-4 Power applying to system, 2-10, 5-6 control of (fig), 2-11, 6-4 removing, 2-11, 6-4 Power and Cooling Modules evaluating LEDs (table), 5-22 LEDs (fig), 5-22 Power backplane installing, 9-8 replacement of (fig), 9-8, 9-9 Power backplane (54-22138-01) removing, 9-6 Index-3 Power connector function of, 1-7 Power cord connection of (fig), 2-10, 5-6 Power cord (U.S.) (17-00083-42), 2-6 configurations included in, D-2 Power module power status assembly (PSA) (70-30585-01) , B-4 Power modules controls, LEDs, connectors (fig), 1-7 functions of, 1-6 location of (fig), 1-5 types of, 1-6 Power modules (fig), 1-6 Power status assembly (PSA) description of, B-4 evaluating LEDs (table), B-5 function of, B-4 LED interpretation (fig), B-5 purpose of, B-4 removal of (fig), 2-37, 3-11, 7-28, 7-29, 7-31, 7-34 Power status assembly (PSA) (70-30585-01) configurations included in, D-3 evaluating LEDs (table), 5-22 location of (fig), 1-6 part number, B-4 removing, 2-37, 7-28, 7-31 Power status assembly (PSA) (70-30585-01) (fig), 4-4, B-5 Power supply filler panel installing, 7-27 replacement of (fig), 7-26, 7-27 Power supply filler panel (74-45749-01) configurations included in, D-3 removing, 7-26 Power switch function of, 1-7 Power system controller (PSC) card (54-22132-01) function of, 1-6, 1-8 removing, 7-32 Power system controller (PSC) card (54-22132-01) (fig), B-6 Preinstallation tasks rack preparation, 2-13 site preparation, 2-2 unpacking, 2-4 Pretest tasks connecting the OBM terminal, 4-2 setting the security switch, 4-4 PSA location of LEDs, B-5 meaning of LEDs, B-5 PSC card installing, 7-33 location of, B-4 replacement of (fig), 7-32, 7-33 Purpose of PSA, B-4 R ------------------------------------------------------------ Rack attaching lower plenum bracket to, 2-18 attaching lower plenum to, 2-19 attaching system to, 3-6 attaching upper plenum to, 3-7 installing clip nuts on, 2-16 positioning clip nuts on, 2-14 Selection of of ((fig)), 2-3 Rack mount kit (70-30580-01), 2-6 contents of, 2-7 Rack preparation, 2-13 Requirements electrical, A-4 environmental, A-6 physical dimensions, A-3 tools, 2-4, 2-9, 2-13, 3-3, 9-1 S ------------------------------------------------------------ Safety symbols definition of (fig), xi SAS port identification of (fig), 1-4, C-2 SCP card removal prerequisites, 6-2 Sections (fig), 1-5 Security switch function of, 1-7 location of, 1-6 use of, 4-4, B-4 Serial port See OBM port Shipping carton contents (fig), 2-6 Site preparation, 2-2 Specifications electrical, A-4 environmental, A-6 physical dimensions, A-3 Status LED function of, 1-7 Switch control processor (SCP) card (DEFGP-AA) configurations included in, D-3 evaluating LEDs on (table), 5-16, 5-21, C-7 function of, 1-8 location of (fig), 1-8 removing, 7-2 Index-4 Switch control processor (SCP) card (DEFGP-AA) (fig), 5-16, C-7 System removing, 8-1 T ------------------------------------------------------------ Temperature, system status LED, B-5 Template function of, 2-7 use of (fig), 2-14 Template, positioning clip nuts with, 2-14 Terminal, OBM connection of (fig), 4-2 Tests, preparation for, 4-1 Tools for module removal, 3-3 for rack preparation, 2-9, 2-13 for unpacking, 2-4, 9-1 U ------------------------------------------------------------ Upper plenum aligning of, 3-7 attaching to the GIGAswitch System, 3-7 function of, 2-7 installation of (fig), 3-7, 8-2 removing, 8-2 V ------------------------------------------------------------ Ventilation, A-7 W ------------------------------------------------------------ Warm boot (fig), 5-7 Index-5