------------------------------------------------------------ Installing the TZ87 Tabletop Cartridge Tape Subsystem Order Number: EK-TZ87T-IG. A01 ------------------------------------------------------------ First Printing, September 1993 © Digital Equipment Corporation 1993. All Rights Reserved. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user 's authority to operate this equipment. The TZ87 shielded interconnect cable as supplied with the unit may not be substituted, nor altered or modified in any way. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna · Increase the separation between the equipment and receiver · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected · Consult the dealer or an experienced radio/TV technician for help The following are trademarks of Digital Equipment Corporation: CleaningTape III, CompacTape II, CompacTape III, VAX, VMS, and the DIGITAL logo. This document was prepared using VAX DOCUMENT, Version 2.1. ------------------------------------------------------------ Preface Introduction Contents This guide describes how to install the TZ87 tabletop cartridge tape subsystem. It provides information about: ------------------------------------------------------------ ------------------------------------------------------------  Unpacking  Configuring the TZ87  Choosing a site  Connecting cables  Affixing decals  Running the power-on self-test ------------------------------------------------------------ Intended Audience This guide is intended for owners of the TZ87 tabletop cartridge tape subsystem. Follow the instructions in the order presented: ------------------------------------------------------------ Task Action ------------------------------------------------------------ 1. Read ``Before You Start'' in the next section to prepare for the installation. 2. Set up the installation. 3. Do the physical installation. 4. Test the installation. ------------------------------------------------------------ v Before You Start Tools Installing the TZ87 tabletop cartridge tape subsystem requires no special tools. If you need to change the switchpack settings on the rear panel, you will need a pointed instrument, such as a pen. Related Documents Along with your system documentation, the following documents supplement this guide: ------------------------------------------------------------ Title Order Number ------------------------------------------------------------ TZ87 Series Cartridge Tape Subsystem Owner 's Manual EK-OTZ87-OM TZ87 Tape Drive Operator 's Reference Card EK-OTZ87-RC ------------------------------------------------------------ To Solve Problems If you have problems during the installation, see Appendix A, Solving Problems, or call Digital Services at your local Customer Support Center. vi 1 ------------------------------------------------------------ Installation Setup 1.1 Overview 1.1.1 How To Set Up the Installation Follow these steps to set up the installation. ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Unpack and check your shipment. 2 Choose a site for the TZ87 tabletop subsystem. 3 Do you need to use foreign language decals? · If yes, affix the decals. · If no, go to step 4. 4 Power off the system on which the TZ87 tabletop subsystem is to be installed. ------------------------------------------------------------ 1.2 Unpack 1.2.1 Check Your Shipment Make sure your shipment has all the items listed on the contents listing. If any item is missing or damaged, contact your delivery agent or your Digital sales representative. ------------------------------------------------------------ Note ------------------------------------------------------------ Save the packing materials until you are sure you will not reship any items. ------------------------------------------------------------ Installation Setup 1-1 Installation Setup 1.2 Unpack 1.2.2 Contents Listing The TZ87 tabletop subsystem and its accessories are: ------------------------------------------------------------ Part Number Description ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ TZ87-TZ87 Tabletop subsystem: a 5-1/4-inch drive in a tabletop enclosure ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ TK85K-01 One CompacTape III cartridge ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ TK85-HC One CleaningTape III cartridge ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 36-28816-03 Sheet of foreign language decals for front panel ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 36-36963-01 Sheet of foreign language decals for remote panel ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ EK-TZ87T-IG Installation Guide ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ EK-OTZ87-OM Owner 's Manual ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ EK-OTZ87-RC Operator 's Reference Card ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ U.S.A. Power cord ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ 12-30552-01 Terminator ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ ------------------------------------------------------------ Standard/ system-specific SCSI signal cable(s) ------------------------------------------------------------ 1.3 Choose a Site 1.3.1 Site Setup Place the TZ87 on a flat, sturdy, level area such as a desk or tabletop-not on the floor. 1.3.2 Site Guidelines Be sure to follow these guidelines for your TZ87: · Avoid a site that is dusty or humid. · Allow enough space around the TZ87 for ventilation and for easy access to the front and rear. 1.4 Affix Decals 1.4.1 For Foreign Language Decals Only If applicable, choose the foreign language decals with the language appropriate for your country. Affix them over the English labels. (See the diagrams in Section 1.4.3.) 1-2 Installation Setup Installation Setup 1.4 Affix Decals 1.4.2 Not Using the Decals? If you are not using the foreign language decals, go to Section 1.5. 1.4.3 Front Decals On the front of the TZ87, one decal adheres to the cartridge insert/release handle; the others adhere to the indicator panel as seen in Figure 1-1: Figure 1-1 Applying Decals (Front) Installation Setup 1-3 Installation Setup 1.4 Affix Decals At the rear of the TZ87, another decal adheres to the remote panel as seen in Figure 1-2. Figure 1-2 Applying Decals (Rear) Decal on Remote PanelðTx ------------------------------------------------------------ SHR-TZ86-03ðTx Installation Setup 1.5 Power Off the System ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Checked and note SCSI IDs. 2 Backed up all disks. 3 Shut down the operating system. 4 Halted the system. 5 Removed power from the system. ------------------------------------------------------------ Installation Setup 1-5 2 ------------------------------------------------------------ Physical Installation 2.1 Overview 2.1.1 How to Install the TZ87 To install the TZ87: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Note the TZ87 factory settings. 2 Review Section 2.2.2. 3 Configure the TZ87 for use on your system: ------------------------------------------------------------ If you need to. . . See page. . . ------------------------------------------------------------ Disable parity checking 2-4 Change the SCSI ID 2-4 ------------------------------------------------------------ 4 Review Section 2.3.1. 5 Connect the cables. ------------------------------------------------------------ Physical Installation 2-1 Physical Installation 2.2 Configure the TZ87 2.2 Configure the TZ87 2.2.1 TZ87 Factory Settings The TZ87 is factory set to SCSI ID 5, the usual ID for tape devices on the SCSI bus. If your system generates parity, the TZ87 can check for correct parity on the SCSI bus. 2.2.2 Configuration Guidelines Your system uses the SCSI ID to identify, or address, the TZ87. Follow these guidelines when configuring the TZ87 for your system: 1. Verify that your drive has a unique SCSI ID from any other device on the SCSI bus. 2. If your drive is the last device on the bus, you must install a terminator on the drive--to terminate the bus. Figure 2-1 shows the location of the DISABLE PARITY and SCSI ID switchpack. 2-2 Physical Installation Physical Installation 2.2 Configure the TZ87 Figure 2-1 ID Switchpack Location ------------------------------------------------------------ SHR-TZ86-04ðTx ------------------------------------------------------------ ðTx OFFðTx ------------------------------------------------------------ 4ðTx ðTx 3ðTx ðTx 2ðTx ðTx 1ðTx SCSI ID LSBðTx ðTx SCSI IDðTx ðTx SCSI ID MSBðTx ðTx DISABLEðTx PARITYðTx ðTx REMOTE PANELðTx ONðTx ------------------------------------------------------------ Physical Installation 2.2 Configure the TZ87 2.2.5 SCSI ID Switch Settings Use the following table to determine SCSI ID switch settings. (See Table 2-1 for switches 2, 3, and 4.) Switch 2 is the most significant bit (MSB) and switch 4 is the least significant bit (LSB): Table 2-1 Switches 1, 2, 3, and 4 ------------------------------------------------------------ Switch (1 = ON; 0 = OFF) ------------------------------------------------------------ SCSI ID 2 3 4 ------------------------------------------------------------ 0 0 0 0 1 0 0 1 2 0 1 0 3 0 1 1 4 1 0 0 Factory Setting 5 1 0 1 6 1 1 0 7 1 1 1 ------------------------------------------------------------ 2.3 Connect the Cables 2.3.1 TZ87 Rear Panel Become familiar with the components on the TZ87 rear panel to complete the physical installation (Figure 2-2): 2-4 Physical Installation Physical Installation 2.3 Connect the Cables Figure 2-2 Rear Panel ðTx SHR-TZ86-05ðTx SCSI SignalðTx Connector (IN)ðTx ------------------------------------------------------------ SCSI Signal ConnectorðTx (OUT/TERMINATION)ðTx PowerðTx SwitchðTx PowerðTx ConnectorðTx Wire CableðTx ClampsðTx ------------------------------------------------------------ Physical Installation 2.3 Connect the Cables 2.3.3 Terminate the SCSI Bus If the TZ87 is the last or only device on the SCSI bus, follow these steps to install the terminator: 1. Connect the SCSI terminator to the rightmost SCSI signal connector on the TZ87 rear panel. 2. Snap the wire cable clamps into place to secure the terminator. If the TZ87 is not the last or only device on the SCSI bus, be sure to install the terminator at the end of the bus. 2.3.4 Connect the Power Cord To connect the power cord, follow these steps: 1. Be sure the TZ87 power switch is set to 0. 2. Connect the power cord to the TZ87 power connector. Make sure the connector is fully seated. 3. Connect the other end of the power cord to a nearby ac outlet. 2-6 Physical Installation 3 ------------------------------------------------------------ Installation Testing 3.1 Overview 3.1.1 To Test the Installation Perform these steps to test the installation: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Turn on system power. 2 Set the power switch on the TZ87 rear panel to on. Result: The power-on self-test (POST) runs automatically when you turn on the TZ87. 3 Observe the TZ87 front panel indicators. 4 Did POST succeed (Section 3.2.1)? · If yes, go to step 5. · If no, see Section 3.2.2. 5 Bring up the system and run the optional system tests. Result: You are ready to operate the TZ87. ------------------------------------------------------------ Installation Testing 3-1 Installation Testing 3.2 Run the Power-On Self-Test 3.2 Run the Power-On Self-Test 3.2.1 POST Success When you turn on system power, the drive performs the POST. The sequence of events follows: ------------------------------------------------------------ Stage What Happens ------------------------------------------------------------ 1 The lights on the right front panel turn on sequentially, from top to bottom. All lights stay on for a few seconds. 2 All lights on the left side turn on at the same time for about three seconds and then turn off. 3 The green Operate Handle, the orange Write Protected, and the yellow Use Cleaning Tape lights turn off. The yellow Tape in Use light blinks while the tape drive initializes. 4 After initialization, if no cartridge is loaded, the yellow Tape in Use light turns off, the green Operate Handle light turns on, the handle unlatches, and the beeper sounds. ------------------------------------------------------------ POST completes in about 13 seconds and the subsystem responds normally to all commands. However, it might take longer for the media to become ready. After a bus reset, the tape drive responds within a bus selection timeout period. 3.2.2 POST Failure If all left- or right-side lights on the TZ87 front panel blink repeatedly, POST did not run successfully. Follow these steps: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Make sure your cable connections are secure. 2 Make sure the SCSI bus is terminated correctly. 3 Power the TZ87 off and then on again to rerun POST. ------------------------------------------------------------ If all front panel indicators blink again, you most likely have a hardware failure. Call Digital Services at your local Customer Support Center. 3-2 Installation Testing Installation Testing 3.3 Bring Up the System 3.3 Bring Up the System 3.3.1 System Startup After successful completion of POST, have the system manager perform the following steps: ------------------------------------------------------------ Step Action ------------------------------------------------------------ 1 Restart the operating system. 2 Configure the system to recognize the TZ87. ------------------------------------------------------------ 3.3.2 Other Tests See your system documentation for instructions on running a full system or SCSI bus test. 3.4 Ready To Operate 3.4.1 For Operating Instructions Once you have verified a successful installation, see the TZ87 Cartridge Tape Subsystem Owner 's Manual (EK-OTZ87-OM) for information on using the TZ87. Installation Testing 3-3 A ------------------------------------------------------------ Solving Problems A.1 What to Do A.1.1 Troubleshooting Chart If the TZ87 fails during power-up or operation, use the following chart to determine the problem and the action to take. If you cannot solve the problem, call Digital Services at your local Customer Support Center. ------------------------------------------------------------ If. . . Then. . . You should. . . ------------------------------------------------------------ Your system does not recognize the TZ87 Your system is not configured to see the SCSI ID Configure your system to see the ID. For example, use SYSGEN AUTOCONFIG on the VMS operating system. The SCSI ID is not unique Change the SCSI ID and reconfigure the system. New ID effective at next power-on. The parameters for your SCSI adapter are incorrect Check your SCSI adapter installation. The SCSI signal cable is loose Make sure the connector on each end of the cable is fully seated. The SCSI terminator is not present or is loose Install the terminator; make sure the terminator is fully seated. Solving Problems A-1 Solving Problems A.1 What to Do ------------------------------------------------------------ If. . . Then. . . You should. . . ------------------------------------------------------------ The SCSI bus is not correctly terminated If the TZ87 is the last or only device on the bus, make sure the terminator is installed on the TZ87. If the TZ87 is not the last or only device on the bus, check the cable connections and make sure the terminator is installed at the end of the bus. The SCSI terminator is not at the end of the bus, or more than two terminators are present Be sure to install a terminator at each end of the bus. One terminator is usually installed at the system. The SCSI bus is too long, or too many devices are on the bus Limit the bus length to the ANSI SCSI standard of 6 meters (19 feet) and the number of devices on the bus (including the system) to eight. Check your system configuration rules. The TZ87 does not power up The TZ87 has no power Check the TZ87 power cord connections, with the TZ87 power switch off. All right or left side lights on the TZ87 front panel blink A drive fault has occurred Press the Unload button on the TZ87 front panel or turn drive power off and then on again to clear the error. If the error does not clear, call Digital Services. You are finding fatal or nonfatal errors for which you cannot determine the cause The bus termination or SCSI signal cable connections may be incorrect Make sure the SCSI bus is terminated. The ac power source grounding may be incorrect Use an ac outlet for the TZ87 on the same ac line that is powering the system. ------------------------------------------------------------ A-2 Solving Problems