dt DECstation 5000 Model 200 Workstation Reference Card © Digital Equipment Corporation 1990 i Table 1. Boot Commands ------------------------------------------------------------ Command Description ------------------------------------------------------------ boot Boots using the boot environment variable. boot 5/tz5/vmunix -a Boots the system software from the tape drive on the base system SCSI connector set at SCSI unit 5. boot 5/rz0/vmunix -a Boots the system software from the optical compact disc drive on the base system SCSI connector set at SCSI unit 0. boot 6/mop -a Boots the system software from the network. ------------------------------------------------------------ Table 2. Configuration Display Commands ------------------------------------------------------------ Command Description ------------------------------------------------------------ cnfg Displays the general configuration for the base system. cnfg 0 Displays a detailed configuration for option slot 0. cnfg 1 Displays a detailed configuration for option slot 1. cnfg 2 Displays a detailed configuration for option slot 2. cnfg 5 Displays a detailed configuration for the SCSI connector in option slot 5. cnfg 6 Displays a detailed configuration for the ThinWire Ethernet connector in option slot 6. cnfg 7 Displays a detailed configuration for the system and memory modules in option slot 7. ------------------------------------------------------------ Table 3. SCSI Commands ------------------------------------------------------------ Command Description ------------------------------------------------------------ cnfg 5 Displays all SCSI devices attached to the base system SCSI controller. init 5 Resets the SCSI devices attached to the base system SCSI controller. t 5/target 5 Tests the unit on the base system's SCSI controller set to SCSI unit 5. t 5/target 5 w Tests the unit on the base system's SCSI controller set to SCSI unit 5. Allows write access during the test. ------------------------------------------------------------ ii Table 4. System Commands ------------------------------------------------------------ Command Description ------------------------------------------------------------ init Resets the system. passwd Enters the current password to gain access to privileged console commands. passwd -s Sets a new password. The password is in effect after the system is reset. passwd -c Clears the existing password. test Tests the entire system. 7/pst-t Tests the base system. 0/pst-t Tests the hardware connected to option slot 0. 1/pst-t Tests the hardware connected to option slot 1. 2/pst-t Tests the hardware connected to option slot 2. 5/pst-t Tests the hardware connected to the SCSI connector (base slot 5). 6/pst-t Tests the cable connected to the ThinWire Ethernet connector (base slot 6). ------------------------------------------------------------ Table 5. Environment Variables ------------------------------------------------------------ Command Description ------------------------------------------------------------ printenv Displays the value of environment variables. setenv variable value Sets the value of an environment variable. unsetenv variable value Deletes an environment variable. (continued on next page) iii Table 5 (Cont.). Environment Variables ------------------------------------------------------------ ------------------------------------------------------------ Variable Description ------------------------------------------------------------ boot The default bootpath specification. Possible values include 5/rz0/vmunix, 5/tz5, 6/mop, and 6/tftp. testaction Selects the level of self-test to be executed automatically. Possible values are q for brief tests and t for more thorough tests. haltaction Specifies what action the console will perform upon powerup or following a reset. Possible values are h = halt, r = restart and b = bootstrap. console Specifies which device is to be used as the console terminal. Value s = use printer port; value 0 = auto configure the console. Use the communications adapter (H8571A) that comes with the workstation to attach the console terminal to the workstation. ------------------------------------------------------------ Table 6. SCSI ID Switch Settings ------------------------------------------------------------ ID Number Hard Disk Drive RRD40 Compact Disc Drive 1 TZ30 Tape Drive 2 TK50Z Tape Drive TLZ04 Tape Drive 3 RX23 Floppy Disk Drive RX33 Floppy Disk Drive ------------------------------------------------------------ 7 Reserved Reserved 6 Up Up Down Down Down Up 5 Up Down Up Down Up Down 4 Up Down Down Down Up Up 3 Down Up Up Up Down Down 2 Down Up Down Up Down Up 1 Down Down Up Up Up Down 0 Down Down Down Up Up Up ------------------------------------------------------------ 1 Switch 4 on the RRD40 optical compact disc drive has no effect on the ID number. 2 Switch 1 (the left switch) on the TZ30 tape drive should always be in the up position. ID switch settings listed for this drive start with switch 2. 3 Switch 1 (the left switch) on the TLZ04 tape drive should always be in the down position. ID switch settings listed for this drive start with switch 2. ------------------------------------------------------------ iv v EK-367AA-IC-002 vi