_ FCO KA650-F001 (DAS), Systems fail to autoboot RA70 during power up ----------------------------------------------------------------------------| | _ _ _ _ _ _ _ | | | | | | | | | | Level of Page 1 | | |d|i|g|i|t|a|l| Urgency Of 4 | | |_|_|_|_|_|_|_| FCO [ F ] | |___________________________________________________________________________| | FIELD CHANGE ORDER Number KA650-F001-DAS | |___________________________________________________________________________| | Applicability: MicroVax 3600, MicroVax 3500, VaxStation 3200 and | | VaxStation 3500 which are experiencing the symptoms described below. | |___________________________________________________________________________| | Problem/Symptoms: Failure of the above mentioned systems to autoboot a | | RA70 during power-up or after a power failure/power-up sequence. | | Additional problem/symptoms addressed in this FCO are listed on Page 2. | | _________________________________________________________________________| | Quick Check: see Page 2 | | | |___________________________________________________________________________| | Compatibility/Prerequisite FCO | Est. Time to Install | | None | 1.0 hrs | |___________________________________________________|_______________________| | Special Tools or Test Equipment: None | |___________________________________________________________________________| | FCO Parts Information | |___________________________________________________________________________| | Order by | Contents | | FCO Kit # |____________________________________________________________| | | Quantity Part Number Description | | EQ-01550-03 | 1 KA650-AA M7620-AA Rev K2 or higher. | | EQ-01550-04 | 1 KA650-BA M7620-BA Rev K2 or higher. | | FA-04855-02 | 1 FCO Document | |______________|____________________________________________________________| | EQ Kit Variation/System-Option Applic: See Page 2. | |___________________________________________________________________________| | Approvals | |___________________________________________________________________________| | CSSE Engineer |F.S. Product Safety | F.S. Logistics | | G. Gazzola | Robert Brister | E. Duggan | |________________________|_________________________|________________________| | Responsible CSSE Mgr |F.S. Microfiche Libraries| Affected Population | | E. Toledo | | 50 | |________________________| VAXDOC EP-FSVDC-LB |_______________________ | | ESD&P Micropublishing | | Initial Kitting | | Diane MacDonald | VAXnotes | 50 | |________________________| STARS |_______________________ | | Revision | | Hardcopy Publication | | A | | 75 | |________________________| |________________________| | FCO Release Date | | Parts Availability | | 17-July-1989 | | July 1989 | +---------------------------------------------------------------------------+ _ _ _ _ _ _ _ | FCO KA650-F001 | | | | | | | | | |d|i|g|i|t|a|l| | PAGE 2 OF 4 |_|_|_|_|_|_|_| | | _______________________________|_________________________________________ Problem/Symptoms (Continued) . Ultrix 3.0 upgrade incompatible with earlier revisions of the CPU. . Failure of the system to autoboot a RA90 during power-up or after a dismount. . Failure of the B/100 XQA0 command. . Technical points 1, 2 and 3 of Customer Letter dealing with DMA transfers, POLY instructions and non-Digital device drives. . Support of DSSI technology for older revisions of CPU board (Rev B-F) . Support of KXJ11 Option. Quick Check: Upon boot, the following banner should be displayed: KA650-A/B V5.3 V2.7 (or greater) EQ Kit Variation/System-Option Applicability: Please read the descriptions below carefully before deciding which kit to use: Kit 1: EQ-01550-02 For systems with multiuser capabilities and license. Kit 2: EQ-01550-03 For systems with single user capability and license. NOTE: THESE BOARDS ARE NOT INTERCHANGEABLE _ _ _ _ _ _ _ | FCO KA650-F001 | | | | | | | | | |d|i|g|i|t|a|l| | PAGE 3 OF 4 |_|_|_|_|_|_|_| | | _______________________________|_________________________________________ INSTALLATION INSTRUCTIONS NOTE: If applicable, spin down and unload any drives that may be on the system prior to powering down. 1. Power down system. ********************************************* * CAUTION * * * * AC POWER MUST BE REMOVED FROM THE * * SYSTEM BEFORE PROCEEDING * ********************************************* 2. Remove the power cord from the power receptacle after powering down. 3. Refer to the appropriate system maintenance manual and gain access to the module area. ******************************************************** * NOTE * * * * THE MODULES IN THIS SYSTEM CONTAIN ELECTROSTATIC * * DISCHARGE SENSITIVE DEVICES. THE USE OF THE * * VELOSTAT KIT IS ESSENTIAL TO PREVENT DAMAGE * * WHICH MAY NOT BE NOTICED IMMEDIATELY * ******************************************************** 4. Set up a VELOSTAT kit in the following manner: a. Unfold the VELOSTAT mat to full size. b. Attach the ground cord to the snap fastener on the VELOSTAT mat. c. Attach the alligator clip end of the ground cord to a good (bare metal) ground on the system. d. Attach the wrist strap to either wrist and the alligator clip to a convenient portion of the mat. 5. Remove the H3600-SA cover and disconnect the ribbon cables between the H3600 and the KA650. 6. Remove the module from the backplane and place on the velostat worksheet. _ _ _ _ _ _ _ | FCO KA650-F001 | | | | | | | | | |d|i|g|i|t|a|l| | PAGE 4 OF 4 |_|_|_|_|_|_|_| | | _______________________________|_________________________________________ 7. Install new CPU module: Seat the module firmly into its backplane slot. Attach the ribbon cables from the H3600-SA to the CPU module. Attach the H3600-SA - close up cab/door. 8. Power up and observe the banner that is displayed - it should read: KA650-A/B* V5.3, VMB2.7 *A = multiuser system B = single user system \^ KA650 \\KA650 \\KA650-F001 \\GAZZOLA \\1989 \\JUL \\FCO_DOCS